manualshive.com logo in svg

Clarion Ungo Pro Security RK1, Installation Manual

Share
Download
Clarion Ungo Pro Security RK1 Installation Manual Download Page 39

39

power-up

The power-up feature ensures that when the security system is powered back up after power has been
disconnected, the system will resume the same state it was in before power was lost. For example, if
power is disconnected during a full trigger sequence, the system will still be in the full trigger
sequence when power is reconnected to the unit. If power is disconnected while the unit is disarmed,
it will still be disarmed when power is restored.

timer mode

By pressing the remote 

and 

buttons the parking lights will flash 4 times and then start the

vehicle and run for the set duration. The remote start can be shut off by the remote by pressing the
remote start button 

and remain in timer mode, but if any other shut down zones or the ignition

becomes active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified duration, unless shut down by the remote

start button 

. If shut down with the remote start button 

the system will remain in timer mode.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.

To exit timer mode, turn the ignition switch on any time the engine is running. The parking lights will
flash 4 times, indicating timer mode has been exited.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.

Summary of Contents for Ungo Pro Security RK1















































Reviews:

No comments

Brands by name

Popular brands

Load more brands