manualshive.com logo in svg

Clarion Ungo Pro Security RK1, Installation Manual

Share
Download
Clarion Ungo Pro Security RK1 Installation Manual Download Page 27

27

programming jumpers

light flash (+)/(-)

This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay
is enabled and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board
relay is disabled. The WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving facto-
ry parking light relays.

N

NO

OTTEE:: For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light

flash output. A standard automotive SPDT relay must be used on the H1/2 light flash output harness wire.

tach threshold on/off

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in
their ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing
the jumper to the ON setting changes the trigger threshold of the digital tach circuit so it will work
properly with these vehicles. The vehicles affected include many newer Dodge/Chrysler/Plymouth
vehicles, such as the Neon, Cirrus, Stratus, Breeze and LH-based vehicles.

TO CHANGE
JUMPER
SETTINGS

LIGHT
FLASH
JUMPER

TACH

THRESHOLD

JUMPER

TACH THRESHOLD OFF (DEFAULT)

TACH THRESHOLD ON

(-) LIGHT FLASH OUTPUT

(+) LIGHT FLASH OUTPUT (DEFAULT)

Summary of Contents for Ungo Pro Security RK1















































Reviews:

No comments

Brands by name

Popular brands

Load more brands