Clarion Ungo Pro Security RK1 Installation Manual Download Page 32

Page: 32 / 46

The remote coding will be exited if:

●

The ignition is turned on.

●

The Override switch is pressed too many times.

●

More than 15 seconds elapses between programming steps.

One long horn honk (if connected) indicates that the remote coding has been exited.

feature menus

Factory default settings are indicated in

bold

in the following feature tables.

FEATURE

DEFAULT - LED ON SETTING

LED OFF SETTING

NUMBER

(PRESS CHANNEL 1)

(PRESS CHANNEL 2)

1-1

Active mode

Passive mode

1-2

Chirps ON

Chirps OFF

1-3

Ignition lock ON

Ignition lock OFF

1-4

Ignition unlock ON

Ignition unlock OFF

1-5

Active locking

Passive locking

1-6

Panic with ignition ON

Panic with ignition OFF

1-7

Door lock pulse duration 0.8 seconds

Door lock pulse duration 3.5 seconds.

1-8

Double Unlock Pulse OFF

Double Unlock Pulse ON

1-9

Channel 2 delayed validity

Channel 2 latched (2), latch reset with ignition
(3), 30 second timed (4)

1-10

FAD with Channel 2 ON

FAD with Channel 2 OFF

1-11

Security features ON

Security features OFF (starter kill)

1-12

Code Hopping ON

Code Hopping OFF

1-13

Channel 4 Validity

Latched, Latch reset with ignition, 30-sec.
timed

OTTEE:: The numbers in parentheses indicate the number of times the LED will flash.

menu #1

Summary of Contents for Ungo Pro Security RK1














































Search results

Summary of Contents for Ungo Pro Security RK1

Reviews:

Brands by name

Popular brands

Clarion Ungo Pro Security RK1, Installation Manual

Search results

Summary of Contents for Ungo Pro Security RK1

Reviews:

Brands by name

Popular brands