manualshive.com logo in svg

Clarion Ungo Pro Security RK1, Installation Manual

Share
Download
Clarion Ungo Pro Security RK1 Installation Manual Download Page 3

3

warning! safety first

IIM

MPPO

ORRTTA

AN

NTT!! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a stan-

dard transmission vehicle is dangerous and is contrary to its intended use.

The following safety warnings must be observed at all times:

●

Due to the complexity of this system, installation of this product must only be performed by an
authorized dealer.

●

When properly installed, this system can start the vehicle via a command signal from the remote
control. Therefore, never operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized dealers
should make the following recommendations to all users of this system:

1. Never operate the system in an enclosed or partially enclosed area without ventilation (such

as a garage). 

2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced,

the remote engine start system must be disabled using the installed toggle switch. 

3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote

controls to assure that the system does not unintentionally remote engine start the vehicle.

4.

THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING
AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS
TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES
REMAIN CLOSED.

Summary of Contents for Ungo Pro Security RK1















































Reviews:

No comments

Brands by name

Popular brands

Load more brands