Clarion DXZ778RUSB Owner'S Manual Download

Page: 46 / 51

English

DXZ778RUSB

7. IN CASE OF DIFFICULTY

Problem

Cause

Measure

General

Power does not
turn on.
(No sound is
produced.)

Fuse is blown.

Replace with a fuse of the same amperage. If the
fuse blows again, consult your store of purchase.

Incorrect wiring.

Consult your store of purchase.

No sound output
when operating
the unit with
amplifiers or
power antenna
attached.

Power antenna lead is
shorted to ground or
excessive current is required
for remote-on the amplifiers
or power antenna.

1. Turn the unit off.
2. Remove all wires attached to the power antenna

lead. Check each wire for a possible short to
ground using an ohm meter.

3. Turn the unit back on.
4. Reconnect each amplifier remote wire to the power

antenna lead one by one. If the amplifiers turn off
before all wires are attached, use an external relay
to provide remote-on voltage (excessive current
required).

Nothing happens
when buttons are
pressed.

Display is not
accurate.

The microprocessor has
malfunctioned due to noise,
etc.

Turn off the power, then press
the [

RELEASE

] button and

remove the DCP.
Press the reset button for about
2 seconds with a thin rod.

DCP or main unit connectors
are dirty.

Wipe the dirt off with a soft cloth moistened with
cleaning alcohol.

No sound heard

The speaker protection circuit
is operating.

1. Turn down sound volume. Function can also be

restored by turning the power off and on again.
(Speaker volume is reduced automatically when
the speaker protection circuit operates).

2. If the sound is muted again, consult our service

department.

CD/MP3/WMA/AAC

No sound heard

MP3/WMA/AAC files are
absent in a disc.

Write MP3/WMA/AAC files onto the disc properly.

Files are not recognized as
an MP3/WMA/AAC file.

Use MP3/WMA/AAC files encoded properly.

File system is not correct.

Use ISO9660 level 1, 2 or JOLIET or Romeo or
APPLE ISO file system.

Sound skips or is
noisy.

Compact disc is dirty.

Clean the compact disc with a soft cloth.

Compact disc is heavily
scratched or warped.

Replace with a compact disc with no scratches.

Sound is cut or
skipped.
Noise is
generated or
noise is mixed
with sound.

MP3/WMA/AAC files are not
encoded properly.

Use MP3/WMA/AAC files encoded properly.

Sound is bad
directly after
power is turned
on.

Water droplets may form on
the internal lens when the car
is parked in a humid place.

Let dry for about 1 hour with the power on.

Wrong filename

File system is not correct.

Use ISO9660 level 1, 2 or JOLIET or Romeo or
APPLE ISO file system.

Reset button

DXZ778RUSB_EN.book 46 ページ２００６年１２月２６日　火曜日　午後２時２５分

Summary of Contents for DXZ778RUSB




















































Search results

Summary of Contents for DXZ778RUSB

Reviews:

Related manuals for DXZ778RUSB

Brands by name

Popular brands

Clarion DXZ778RUSB, Owner'S Manual

Search results

Summary of Contents for DXZ778RUSB

Reviews:

Related manuals for DXZ778RUSB

Brands by name

Popular brands