11
EN
CLAGE
Pos.
Function
1
Status display, top
2
User selection
3
Applications
4
Temperature display
5
Status display, bottom
6
Main menu
7
Temperature setting
Display informations (fig. A1)
Temperature display
The coloured scale ring fills up as the temperature setting is increased and the colour changes
from blue when the temperature is low to red when the
temperature is high. In addition, the target temperature is displayed in °C as a figure in the mid-
dle of the display.
Temperature setting
The desired temperature can be selected by tapping on
and
for the fine setting or by
dragging along the coloured scale ring for a quick selection within a range of 20 °C to 60 °C.
Tapping
or
once changes the temperature by 1 °C, in the comfort range between 35
and 43 °C by 0.5 °C. If the temperature is set below 20 °C, the symbol
appears in the tem-
perature display and the appliance switches off the heating function.
User selection
Up to eight user profiles can be created. Every user has the option to save his desired tempera-
tures for the different uses in a profile. The user profiles can be selected by tapping on the profile
image (fig. A2) and the temperatures saved in the profile are set (to create profile, see Section
“User”).
Applications
Preset applications can be selected here. Simply tap on the desired symbol (fig. A3).
The temperatures set at the factory (
handwash = 35 °C,
shower = 38 °C,
bath = 42 °C,
hot water = 48 °C) can be changed for each application via the tempera-
ture setting. If you touch the temperature value in the temperature display or the application sym-
bol for 3 seconds, the temperature is saved for the selected application. The temperature display
flashes once for confirmation. Application temperatures saved in the user profile can be called up
at any time by tapping on the corresponding symbol.
Status display, top
Control lock active (PIN)
The inlet temperature exceeds the target value (appliance does not heat up)
Indication of activated Wi-Fi. The amount of bars indicates the signal strength
Indication of activated Bluetooth
Indication of a successful connection to CLAGE Cloud
Status display, bottom
Display area for functions which require confirmation from the user or which are of great signifi-
cance.
Eco active: The outlet temperature for all applications and the water flow are limited to
an energy-efficient value. If the temperature is set higher via the temperature setting,
the symbol start to flash.
Maintenance: Tap the symbol to open a status message with additional information.
Maximum temperature reached: The temperature cannot be increased any further
since the set temperature limit has been reached. The temperature limit can be
changed in the main menu under “Settings”.
2. How to use
Main control
The display shows the main control by default. The current status is displayed and by tapping on
the touch screen you get access to various submenus and functions.
Drawing mode
If heated water is drawn from a tap, the main control changes to drawing mode and, depending
on the set outlet temperature, changes the background colour from blue for low temperatures
to red for high temperatures (fig. A4). In this mode the scale ring displays the actual power
consumption of the appliance.
Main menu
All function menus and saved values of the appliance can be selected from here. Tap on the
symbol to go back to the main control (fig. A5).
• Plastic surfaces and fittings should only be wiped with a damp cloth. Do not use abrasive or
chlorine-based cleaning agents or solvents.
• For a good water supply, the outlet fittings (special tap aerators and shower heads) should
be unscrewed and cleaned at regular intervals. Every three years, the electrical and plumb-
ing components should be inspected by an authorised professional in order to ensure proper
functioning and operational safety at all times.
Cleaning and maintenance
This instantaneous water heater features an automatic air bubble pro-
tection to prevent it from inadvertently running dry. Nevertheless, the
appliance must be vented before using it for the first time. Each time the
appliance is emptied (e.g. after work on the plumbing system, if there is
a risk of frost or following repair work), the appliance must be re-vented
before it is used again.
1. Disconnect the instantaneous water heater from the mains (e.g. via deactivating the fuses).
2. Unscrew the jet regulator on the outlet fitting and open the cold water tap valve to rinse out
the water pipe and avoid contaminating the appliance or the jet regulator.
3. Open and close the hot water tap until no more air emerges from the pipe and all air has
been eliminated from the water heater.
4. Only then should you re-connect the power supply again (e.g. via activating the fuses) to the
instantaneous water heater and screw the jet regulator back in.
5. The appliance activates the heater after approx. 10 seconds of continuous water flow.
Venting after maintenance work
For further informations please use the online operation and installation
instruction. Please follow the link below or use the QR code via smart-
phone or tablet.
https://www.clage.de/links/gma/DSX-Touch-GMA-9120-34385
