Cisco WRT350N User Manual Download | Manualshive

Page: 68 / 93

background image

61

Appendix A: Troubleshooting
Common Problems and Solutions

Wireless-N Gigabit Router with Storage Link

11. To start over, I need to set the Router to factory defaults.

Hold the

Reset

button for five seconds and then release it. This will return the password, forwarding, and

other settings on the Router to the factory default settings. In other words, the Router will revert to its original
factory configuration.

12. I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download
the latest firmware at www.linksys.com.
Follow these steps:

1. Go to the Linksys website at

http://www.linksys.com

and download the latest firmware.

2. To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

13. The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or
make the Power LED stop flashing:
•

If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open
the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s
instructions.

•

Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following
IP address settings for the computer you are using:

IP Address: 192.168.1.50
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

•

Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

14. My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a
period of inactivity, just like a normal phone dial-up connection to the Internet.
•

There is a setup option to “keep alive” the connection. This may not always work, so you may need to re-
establish connection periodically.

1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the

Router.

2. Enter the password, if asked. (The default password is admin.)
3. On the

Setup

screen, select the option

Keep Alive

, and set the Redial Period option at 20 (seconds).

4. Click the

Save Settings

button.

5. Click the

Status

tab, and click the

Connect

button.

6. You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you

see the login status display as Connected.

•

Click the

Save Settings

button to continue.

•

If the connection is lost again, follow steps 1- 6 to re-establish connection.

«
...
66
67
68
69
70
...
»

Summary of Contents for WRT350N






























































































Reviews:

No comments

Related manuals for WRT350N

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

Brand: D-Link Pages: 176

Brand: LORD Pages: 9

Brand: TP-Link Pages: 2

Brand: Kanguru Pages: 13

Brand: 4G Systems Pages: 2

Brand: H3C Pages: 4

Brand: Connectland Pages: 10

AceroDURO 100/S100

Brand: CNC-Step Pages: 86

Brand: FiberHome Pages: 2

Brand: TRENDnet Pages: 68

Edge-Core A07-ES4548C

Brand: Atlantis Land Pages: 2

Brand: H3C Pages: 62

TeleLite 720920 Series

Brand: Positron Pages: 21

Brand: bintec elmeg Pages: 32

BNI EIP-508 05-Z015 Series

Brand: Balluff Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands