Cisco UCS 6400 Series Hardware Installation Manual Download

Page: 17 / 68

Description

State

Color

Function

Location

LED

Normal
operation

Solid on

Green

Indicate system
power/health at bootup
and run time

Front and rear

System
Status LED

System
powered off

Off

System
fault

Amber

Power shut
down by
software

Solid on

Red

Secure boot
validation
has failed

Blinking

Network Management Port LEDs

The states of the LEDs of the management port on the front panel are listed below.

Description

LED State

LED Position

No link

Off

Left

Physical link

Solid green

No activity

Off

Right

Activity

Blinking green

L1 and L2 Port LEDs

The states of the LEDs on the L1 and L2 front-panel ports are listed below.

Description

LED State

LED Position

No link

Off

Left

Physical link

Solid green

Left

No activity

Off

Right

Activity

Blinking green

Right

Cisco UCS 6400 Series Fabric Interconnect Hardware Installation Guide

Product Overview

Network Management Port LEDs

Summary of Contents for UCS 6400 Series




































































Search results

Summary of Contents for UCS 6400 Series

Reviews:

Related manuals for UCS 6400 Series

Brands by name

Popular brands

Cisco UCS 6400 Series, Hardware Installation Manual

Search results

Summary of Contents for UCS 6400 Series

Reviews:

Related manuals for UCS 6400 Series

Brands by name

Popular brands