manualshive.com logo in svg

Cisco UCS 6400 Series, Hardware Installation Manual, Page: 42 / 68

Share
Download
Cisco UCS 6400 Series Hardware Installation Manual Download Page 42

Configuration file - Ok

Cisco UCS 6454 Fabric Interconnect

FI-B login:

Step 13

If necessary, upgrade the UCS Manager software. If the replacement fabric interconnect is not running the
same firmware version as the cluster, the setup utility can upgrade the firmware.

Example:

---- Basic System Configuration Dialog ----

This setup utility will guide you through the basic configuration of
the system. Only minimal configuration including IP connectivity to
the Fabric interconnect and its clustering mode is performed through
these steps.

Type Ctrl-C at any time to abort configuration and reboot system.
To back track or make modifications to already entered values,
complete input till end of section and answer no when prompted
to apply configuration.

Enter the configuration method. (console/gui) ? console

Installer has detected the presence of a peer Fabric interconnect.
This Fabric interconnect will be added to the cluster. Continue (y/n) ? y

Enter the admin password of the peer Fabric interconnect:

Connecting to peer Fabric interconnect... done
Retrieving config from peer Fabric interconnect... done
Installer has determined that the peer Fabric Interconnect is
running a different firmware version than the local Fabric.
Cannot join cluster.

Local Fabric Interconnect

UCSM version

: 3.1(2c)

Kernel version

: 5.0(3)N2(3.12b)

System version

: 5.0(3)N2(3.12b)

local_model_no

: UCS-FI-6454

Peer Fabric Interconnect

UCSM version

: 3.1(2c)

Kernel version

: 5.0(3)N2(3.12c)

System version

: 5.0(3)N2(3.12c)

peer_model_no

: UCS-FI-6454

Do you wish to update firmware on this Fabric Interconnect to the
Peer's version? (y/n): y
Updating firmware of Fabric Interconnect.......
[ Please don't press Ctrl+c while updating firmware ]

Updating images
Please wait for firmware update to complete.

<output truncated>

Install has been successful.
Firmware Updation Successfully Completed. Please wait to enter the IP address

Peer Fabric interconnect Mgmt0 IPv4 Address: xx.xx.xx.xx
Peer Fabric interconnect Mgmt0 IPv4 Netmask: xx.xx.xx.xx
Cluster IPv4 address

: xx.xx.xx.xx

Cisco UCS 6400 Series Fabric Interconnect Hardware Installation Guide

36

Replacing Components

Shutting Down a Fabric Interconnect

Summary of Contents for UCS 6400 Series





































































Reviews:

No comments