Cisco SVP2000P Page 33 User Manual Download

Page: 33 / 51

STEPHEN TECHNOLOGIES CO.,LIMITED

/ 5/F, Building NO.1, TongXin Industry Zone, HengGang, LongGang, Shenzhen, G.D, China, 518115

Tel: +86 755 89352606 /Fax:+86 755 89352612 / Email:

Handdown Time

Specify the least reflection time of Handdown, the default is 200ms.

Ring Type

Select Ring Type

Output Volume

Specify Output (receiver) Volume grade.

Ring Volume

Specify Ring Volume grade

G722 Timestamps

160/20ms or 320/20ms is available

G723 Bit Rate

5.3kb/s or 6.3kb/s is available

Default Ring Type

Set up the ring by default

Signal Standard

Select Signal Standard.

VAD

Select it or not to enable or disable VAD.

over 20ms.

4.3.4.2. Call Service

In this web page, you can configure Hotline, Call Transfer,

Field name

Hotline

Specify Hotline number. If you set

No Answer

Time

Specify No Answer Time

P2P IP Prefix

Set Prefix in peer to peer IP call. For example

IP Prefix as 192.168.1., you dial only #119 to

means to disable dialing IP.

Remote Record

Set Remote Record number

Do Not Disturb

Select NO Disturb, the phone will reject any incoming call, the callers will be reminded by busy, but any

outgoing call from the phone will work well.

Ban Outgoing

If you select Ban Outgoing to enable it, and you can not dial out any number.

Enable Call

Transfer

Enable Call Transfer by selecting it.

SVP2000PP Business

/ 5/F, Building NO.1, TongXin Industry Zone, HengGang, LongGang, Shenzhen, G.D, China, 518115

/Fax:+86 755 89352612 / Email: [email protected] / Url: www.stephen-tele.com

Specify the least reflection time of Handdown, the default is 200ms.

Select Ring Type

(receiver) Volume grade.

Specify Ring Volume grade

320/20ms is available

5.3kb/s or 6.3kb/s is available

Set up the ring by default

Select Signal Standard.

Select it or not to enable or disable VAD. If enable VAD, G729 Payload length could not be

Hotline, Call Transfer, Call Waiting, 3 Ways Call, Black List, white list Limit List and so on.

Call Service

explanation

Specify Hotline number. If you set the number, you can not dial any other numbers.

Set Prefix in peer to peer IP call. For example: what you want to dial is 192.168.1.119, If you define P2P

IP Prefix as 192.168.1., you dial only #119 to reach 192.168.1.119. Default is “.”. If there is no “.” Set, it

means to disable dialing IP.

number. Via dialing this number, you can hear all voice records in your VoIP server.

phone will reject any incoming call, the callers will be reminded by busy, but any

outgoing call from the phone will work well.

If you select Ban Outgoing to enable it, and you can not dial out any number.

Transfer by selecting it.

Business POE IP Phone User Manual

/ 5/F, Building NO.1, TongXin Industry Zone, HengGang, LongGang, Shenzhen, G.D, China, 518115

tele.com

- 33 -

Specify the least reflection time of Handdown, the default is 200ms.

If enable VAD, G729 Payload length could not be set

, 3 Ways Call, Black List, white list Limit List and so on.

the number, you can not dial any other numbers.

what you want to dial is 192.168.1.119, If you define P2P

reach 192.168.1.119. Default is “.”. If there is no “.” Set, it

all voice records in your VoIP server.

phone will reject any incoming call, the callers will be reminded by busy, but any

If you select Ban Outgoing to enable it, and you can not dial out any number.

Summary of Contents for SVP2000P




















































Search results

Summary of Contents for SVP2000P

Reviews:

Related manuals for SVP2000P

Brands by name

Popular brands

Cisco SVP2000P, User Manual

Search results

Summary of Contents for SVP2000P

Reviews:

Related manuals for SVP2000P

Brands by name

Popular brands