Cisco SVP2000P User Manual Download

Page: 18 / 51

SVP2000PP Business POE IP Phone User Manual

STEPHEN TECHNOLOGIES CO.,LIMITED

/ 5/F, Building NO.1, TongXin Industry Zone, HengGang, LongGang, Shenzhen, G.D, China, 518115

Tel: +86 755 89352606 /Fax:+86 755 89352612 / Email: [email protected] / Url: www.stephen-tele.com

- 18 -

Obtain DNS server

automatically

Select it to use DHCP mode to get DNS address, if you don’t select it, you will use static DNS

server. The default is selecting it.

If you use static mode, you need set it.

IP Address

Input the IP address distributed to you.

Netmask

Input the Netmask distributed to you.

Gateway

Input the Gateway address distributed to you.

DNS Domain

Set DNS domain postfix. When the domain which you input can not be parsed, phone will

automatically add this domain to the end of the domain which you input before and parse it

again.

Primary DNS

Input your primary DNS server address.

Alter DNS

Input your standby DNS server address.

If you uses PPPoE mode, you need to make the above setting.

PPPoE Server

It will be provided by ISP.

Username

Input your ADSL account.

Password

Input your ADSL password.

Notice:

1)Click “Apply” button after finished your setting, IP Phone will save the setting automatically and new setting will take

effect.

2)If you modify the IP address, the web will not response by the old IP address. Your need input new IP address in the

address column to logon in the phone.

3)If networks ID which is DHCP server distributed is same as network ID which is used by LAN of system, system will use

the DHCP IP to set WAN, and modify LAN’s networks ID(for example, system will change LAN IP from 192.168.10.1 to

192.168.11.1) when system uses DHCP client to get IP in startup; if system uses DHCP client to get IP in running status

and network ID is also same as LAN’s, system will refuse to accept the IP to configure WAN. So WAN’s active IP will be

0.0.0.0

4.3.2.2. LAN Config

LAN Config

Field name

explanation

Summary of Contents for SVP2000P




















































Search results

Summary of Contents for SVP2000P

Reviews:

Related manuals for SVP2000P

Brands by name

Popular brands

Cisco SVP2000P, User Manual

Search results

Summary of Contents for SVP2000P

Reviews:

Related manuals for SVP2000P

Brands by name

Popular brands