Cisco PA-POS-2OC3 Installation And Configuration Manual Download Page 96

Page: 96 / 100

4-28

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 4 Configuring the PA-POS-2OC3

Checking the Configuration

Keepalive not set

Scramble disabled

Last input 00:24:38, output 02:58:40, output hang never

Last clearing of "show interface" counters 00:00:52

Input queue:0/75/0/0 (size/max/drops/flushes); Total output drops:0

Queueing strategy:fifo

Output queue:0/40 (size/max)

5 minute input rate 366000 bits/sec, 953 packets/sec

5 minute output rate 2977000 bits/sec, 7476 packets/sec

100 packets input, 856 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 parity

8 input errors, 8 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 applique, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Cisco 7600 Series Routers with FlexWAN and Enhanced FlexWAN—Example Output of the show interfaces Command

Following is an example of the

show interfaces pos

command that shows a PA-POS-2OC3 in slot 1 in

a FlexWAN module in a Cisco 7609 router (slot 8):

Router#

show interfaces pos 8/1/0

POS8/1/0 is down, line protocol is down

Hardware is Packet over Sonet

Description: SMB 5B1

Internet address is 192.85.10.1/24

MTU 4470 bytes, BW 155000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation PPP, crc 16, loopback not set

Keepalive set (10 sec)

Scramble enabled

LCP Closed

Closed: IPCP, CDPCP

Last input never, output never, output hang never

Last clearing of "show interface" counters 2w6d

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

30 second input rate 0 bits/sec, 0 packets/sec

30 second output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 parity

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 applique, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Summary of Contents for PA-POS-2OC3





































































































Search results

Summary of Contents for PA-POS-2OC3

Reviews:

Brands by name

Popular brands

Cisco PA-POS-2OC3, Installation And Configuration Manual

Search results

Summary of Contents for PA-POS-2OC3

Reviews:

Brands by name

Popular brands