manualshive.com logo in svg

Cisco PA-POS-2OC3, Installation And Configuration Manual

Share
Download
Cisco PA-POS-2OC3 Installation And Configuration Manual Download Page 86

4-18

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 4      Configuring the PA-POS-2OC3

  Checking the Configuration

0x00: 04 FF 40 03 E3 41 01 00 C1 8B 4A 41 45 30 38 30

 

0x10: 32 31 36 46 42 82 49 20 1C 02 42 41 30 03 00 81

 

0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 50 41 2D

 

0x30: 50 4F 53 2D 32 4F 43 33 20 20 20 20 20 20 20 20

 

0x40: 20 C0 46 03 20 00 55 61 02 FF FF FF FF FF FF FF

 

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Cisco 7304 Router—Example Output of the show diag Command

Following is an example of the 

show diag 

command for a PA-POS-2OC3 in router module slot 5 of a 

Cisco 7304 router:

Router# 

show diag 5

Slot 5: is a PA CC with the following PA in its slot0:

Slot 0:

        Dual OC3 POS Port adapter, 2 ports

        Port adapter is analyzed 

        Port adapter insertion time 00:01:02 ago

        EEPROM contents at hardware discovery:

        Hardware Revision        : 1.0

        PCB Serial Number        : JAE0826MGXV

        Part Number              : 73-8220-03

        Board Revision           : A0

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Deviation Number         : 0

        Product Number           : PA-POS-2OC3         

        Top Assy. Part Number    : 800-21857-03

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 E3 41 01 00 C1 8B 4A 41 45 30 38 32

          0x10: 36 4D 47 58 56 82 49 20 1C 03 42 41 30 03 00 81

          0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 50 41 2D

          0x30: 50 4F 53 2D 32 4F 43 33 20 20 20 20 20 20 20 20

          0x40: 20 C0 46 03 20 00 55 61 03 FF FF FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

BCM1125 LDT Host Bridge, handle=0

BCM bridge, config=0x0

(0x00):dev, vendor id              = 0x0002166D

(0x04):status, command             = 0x00100107

(0x08):class code, revid           = 0x06000003

(0x0C):hdr, lat timer, cls         = 0x00010000

(0x18):bus id registers            = 0x00000000

(0x1C):secondary status            = 0x000001F1

(0x20):mem base/limit              = 0x0000FFF0

(0x30):io upper limit/base         = 0x000001FF

(0x34):capabilities ptr            = 0x00000040

(0x38):expansion rom bar           = 0x00000000

(0x3C):bridge ctrl                 = 0x00220000

(0x40):LDT cmd, cap id,            = 0x20010008

(0x44):Link config/control         = 0x00000000

(0x48):Link frequency              = 0x801F0023

(0x50):SRIcmd, srirxden, sritxden  = 0x00001010

(0x54):SRI tx numerator            = 0x0000FFFF

(0x58):SRI rx numerator            = 0x0000FFFF

(0x68):Error status/control        = 0x00000000

Summary of Contents for PA-POS-2OC3





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands