Cisco Nexus 2000 Series Installation Manual Download Page 155 | Manualshive

Page: 155 / 190

background image

B-1

Cisco Nexus 2000 Series Hardware Installation Guide

A P P E N D I X

B

Technical Specifications

This appendix describes the technical specifications for the Cisco Nexus Fabric Extenders (FEXs) and
includes the following sections:

•

Power Specifications, page B-1

•

Environmental Specifications, page B-6

•

Physical Specifications, page B-6

•

Transceiver Specifications, page B-7

•

Airflow Optimization Accessories, page B-9

Note

Specifications for cables and connectors are provided in

Appendix C, “Cable and Port Specifications.”

Power Specifications

This section describes the power specifications for the Cisco Nexus Fabric Extenders.

The power supplies connect directly to the system through connectors attached to the baseboard through
cables. One connector is on the baseboard for each power supply. AC input is through an IEC connector
mounted on the power supply port side exhaust panel.

lists the specifications for the FEX

power supplies.

«
...
153
154
155
156
157
...
»

Summary of Contents for Nexus 2000 Series































































































































































































Reviews:

No comments

Related manuals for Nexus 2000 Series

Brand: Rabbit Pages: 45

Brand: Rabbit Pages: 174

Brand: Rabbit Pages: 43

Brand: Barracuda Networks Pages: 2

Brand: Mackie Pages: 2

Brand: Mackie Pages: 5

CNPS7000A Series

Brand: ZALMAN Pages: 9

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brand: Idis Pages: 16

Brand: ZIMO Pages: 13

Brand: Active Communications Pages: 10

Brand: VideoWave Pages: 12

Brand: ZyXEL Communications Pages: 23

Brand: Altimium Pages: 12

Kontron CP3005 Series

Brand: S&T Pages: 115

Braswell Series

Brand: Intel Pages: 54

Brand: TEC Control Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands