manualshive.com logo in svg

Cisco Nexus 2000 Series, Installation Manual

Share
Download
Cisco Nexus 2000 Series Installation Manual Download Page 75

 

2-17

Cisco Nexus 2000 Series Hardware Installation Guide

 

Chapter 2      Using a Fabric Extender with a Cisco Nexus 7000 Series Switch

    Cisco Nexus 2232TM FEX

Figure 2-17

Rear View of the Cisco Nexus 2232TM Chassis

For LED descriptions, see 

Appendix E, “LEDs.”

This section includes the following topics:

•

Ports for the Cisco Nexus 2232TM FEX, page 2-17

•

Power Supplies for the Cisco Nexus 2232TM FEX, page 2-18

•

Fan Tray for the Cisco Nexus 2232TM FEX, page 2-19

•

Transceivers and Connectors Supported by the Cisco Nexus 2232TM FEX, page 2-20

Ports for the Cisco Nexus 2232TM FEX

The downlink and uplink ports are numbered from top to bottom and then from left to right as shown in 

Figure 2-23

.

3

2

4

239278

1

1

Status (top) and ID (bottom) LEDs

3

1- and 10-Gigabit host-facing Ethernet (downlink) ports 
(48)

2

HDMI port

4

10-Gigabit network-facing Ethernet (uplink) ports (8)

Summary of Contents for Nexus 2000 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands