manualshive.com logo in svg

Cisco Nexus 2000 Series, Installation Manual

Share
Download
Cisco Nexus 2000 Series Installation Manual Download Page 121

C H A P T E R

 

4-1

Cisco Nexus 2000 Series Hardware Installation Guide

 

4

Installing a Cisco Nexus Fabric Extender

This chapter describes how to install the Cisco Nexus Fabric Extenders (FEXs) and includes the 
following sections:

•

Preparing for Installation, page 4-2

•

Installing the Cisco Nexus Fabric Extender Chassis in a Cabinet or Rack, page 4-6

•

Grounding the System, page 4-7

•

Grounding the Chassis, page 4-14

•

Starting the Cisco Nexus Fabric Extender, page 4-14

•

Removing and Installing Components, page 4-16

•

Repacking the Cisco Nexus Fabric Extender for Return Shipment, page 4-23

Note

Before you install, operate, or service the system, read the 

Regulatory Compliance and Safety 

Information 

for important safety information.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you 
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar 
with standard practices for preventing accidents. Use the statement number provided at the end of 
each warning to locate its translation in the translated safety warnings that accompanied this device. 

Statement 1071

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be 
accessed only through the use of a special tool, lock and key, or other means of security. 

Statement 1017

Warning

Only trained and qualified personnel must be allowed to install, replace, or service this equipment. 

Statement 1030

Summary of Contents for Nexus 2000 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands