Cisco Nexus 2000 Series Installation Manual Download Page 143

Page: 143 / 190

4-23

Cisco Nexus 2000 Series Hardware Installation Guide

Chapter 4 Installing a Cisco Nexus Fabric Extender

Repacking the Cisco Nexus Fabric Extender for Return Shipment

Step 6

Gently slide the chassis toward you, off of the slider rails and out of the rack.

Repacking the Cisco Nexus Fabric Extender for Return Shipment

If you need to return the Cisco Nexus 2000 and 2300 Series FEX, remove the device from the rack by
following the steps in the

“Removing the Cisco Nexus Fabric Extender” section on page 4-22

, and

repack it for shipment. If possible, use the original packing materials and container to repack the device.
Contact your Cisco customer service representative to arrange for return shipment to Cisco.

Summary of Contents for Nexus 2000 Series































































































































































































Search results

Summary of Contents for Nexus 2000 Series

Reviews:

Brands by name

Popular brands

Cisco Nexus 2000 Series, Installation Manual

Search results

Summary of Contents for Nexus 2000 Series

Reviews:

Brands by name

Popular brands