Cisco NCS 5700 Series Hardware Installation Manual Download Page 53

Page: 53 / 120

Screw thread adapter at the
Front End- Outer slider
member

Rear End- Outer slider
member

Outer slider member

(

NC55-2RU-ACC-SL2

) Adjust the slider (push and pull) to place and fix the slider behind the front post. Attach

the slider to the front post with 2 counter sink screws (10-32) and washers. See

Figure 34: Rear and Front End

(NC55-2RU-ACC-SL2) of the Outer Slider Member

Remove the screw thread adapter present at the front end of the outer slider member if you are unable to
pass the slider through the rack holes. Tighten the screws later after passing the slider through the rack
holes.

Note

Figure 34: Rear and Front End (NC55-2RU-ACC-SL2) of the Outer Slider Member

Counter sink screws

Screw thread adapter at the
Front End- Outer slider
member

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Install the Chassis

Rack Mount the NCS-57C3-MOD Chassis in a 4-Post Rack using Sliders

Summary of Contents for NCS 5700 Series
























































































































Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands

Cisco NCS 5700 Series, Hardware Installation Manual

Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands