manualshive.com logo in svg

Cisco NCS 5700 Series, Hardware Installation Manual

Share
Download
Cisco NCS 5700 Series Hardware Installation Manual Download Page 15

12-Port 10GE with SFP+

The 12-port 10GE MPA (NC55-MPA-12T-S) provides 12 ports for SFP+ transceivers.

ATTN LED

3

STATUS LED

1

SFP+ ports and LEDs

2

4-Port 800GE MPA with QSFP28/QSFP-DD

Table 3: Feature History Table

Description

Release Information

Hardware

This release introduces a 4-port
800GE modular port adapter
(NC57-MPA-2D4H-S) that
supports QSFP28 and QSFP-DD
optical transceivers. This MPA is
supported in the NCS-55A2-MOD
and NCS-57C3-MOD routers. This
is the first modular port adapter to
support the QSFP-DD optical
transceiver.

For port configuration details, see
the "4-Port 800GE MPA with
QSFP28/QSFP-DD" section in

4-Port 800GE MPA with
QSFP28/QSFP-DD

and

Hardware

Installation Guide for Cisco NCS
5700 Series Fixed-Port Routers.

Release 7.4.1

NC57-MPA-2D4H-S modular port
adapter

The NC57-MPA-2D4H-S modular port adapter supports QSFP28 and QSFP-DD optical transceivers in the
following configurations:

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

9

NCS 5700 Router Overview

Modular Port Adapters

Summary of Contents for NCS 5700 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands