Cisco NCS 5700 Series Hardware Installation Manual Download Page 42

Page: 42 / 120

Figure 24: 2-Post Rack Mount

Rack Mount the NCS-57C3-MOD Chassis in a 2-Post Rack

This section describes how to use the rack-mount kit provided with the chassis, to install the following chassis
into a cabinet or a 2-post rack:

• NCS-57C3-MOD-S

• NCS-57C3-MOD-SE-S

If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Caution

The following table lists the items contained in the rack-mount kit provided with the routers.

Table 8: Router Rack-Mount Kit

Part Description

Quantity

Rack-mount brackets

M4 x 6-mm Phillips counter sink screws

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Install the Chassis

Rack Mount the NCS-57C3-MOD Chassis in a 2-Post Rack

Summary of Contents for NCS 5700 Series
























































































































Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands

Cisco NCS 5700 Series, Hardware Installation Manual

Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands