Cisco NCS 5700 Series Hardware Installation Manual Download Page 102

Page: 102 / 120

Figure 76: Handling a Modular Port Adapter

Metal Carrier

Printed Circuit Board

ESD Strap

Online Insertion and Removal

Cisco NCS 5700 series modular port adapters (MPAs) support online insertion and removal (OIR).

Modular port adapters (MPAs) support the following types of OIR:

• Soft OIR

Soft OIR uses the IOS XR

hw-module subslot rack/slot/subslot reload

hw-module subslot

rack/slot/subslot shutdown

, and

no hw-module subslot rack/slot/subslot shutdown

commands to

complete online insertion and removal.

• Managed OIR

A managed online insertion and removal of Modular port adapters (MPAs) is comprised of the following
steps:

• Shut down the MPA with the

hw-module subslot rack/slot/subslot shutdown

command.

• Confirm that the LEDs have gone from green to off.

• Execute the

do show platform

command to verify that the MPA to be removed is in the disabled

state.

• Physically remove the MPA to be replaced.

• Physically insert the replacement MPA

• Return the MPA to the up state with the

no hw-module subslot rack/slot/subslot shutdown

command.

• Hard OIR

You can perform the OIR in a running system by performing the following steps, without executing any
commands:

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Replace Chassis Components

Online Insertion and Removal

Summary of Contents for NCS 5700 Series
























































































































Search results

Summary of Contents for NCS 5700 Series

Reviews:

Brands by name

Popular brands

Cisco NCS 5700 Series, Hardware Installation Manual

Search results

Summary of Contents for NCS 5700 Series

Reviews:

Brands by name

Popular brands