manualshive.com logo in svg

Cisco NCS 5700 Series, Hardware Installation Manual

Share
Download
Cisco NCS 5700 Series Hardware Installation Manual Download Page 112

By default, the display shows all ports and their status. You can change the display mode to show only ports
that are in yellow (YL) state by pressing the DISPLAY button for less than 4 seconds and release. To return
to the default behavior, press and hold the DISPLAY button for more than 5 seconds and release.

Table 17: NCS-57C3 Port Status LED Display

Description

LED Display

Port is administratively enabled, link is up.

GN

Port is administratively shut down; or port is
administratively enabled, link is down.

YL

MPA LEDs

The STATUS LED is located on the front left of the MPA and the attention (ATTN) is located on the front
right of the MPA. The Link LED for each port is located either between the two rows of ports (each of these
LEDs is a triangle pointing to the port above or below the LED) or under the port.

Status

Color

LED

The operator has activated this LED to identify this MPA in the
chassis.

Flashing blue

ATTN

This LED is not being used.

Off

This MPA is operational.

Green

STATUS

Either of the following conditions:

• The MPA has detected a slot ID parity error and will not power

on or boot up.

• The MPA is not fully inserted.

Amber

The MPA is booting up or shutting down.

Flashing amber

The MPA is powered-off and can now be safely removed.

Off

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

106

LEDs

MPA LEDs

Summary of Contents for NCS 5700 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands