Cisco NCS 5700 Series Hardware Installation Manual Download Page 39

Page: 39 / 120

Figure 22: Two Post Rack Type

Rack Mount the Chassis

The chassis can be mounted on a 2-post or a 4-post rack.

•

Rack Mount the NCS-57B1 Chassis in a 2-Post Rack, on page 34

— Contains the procedure for mounting

the NCS-57B1-6D24-SYS and NCS-57B1-5DSE-SYS chassis in a 2-post rack.

•

Rack Mount the NCS-57C3-MOD Chassis in a 2-Post Rack, on page 36

— Contains the procedure for

mounting the NCS-57C3-MOD-S and NCS-57C3-MOD-SE-S chassis in a 2-post rack.

•

Rack-Mount the NCS-57B1 Chassis in a 4-Post Rack, on page 38

— Contains the procedure for mounting

the NCS-57B1-6D24-SYS and NCS-57B1-5DSE-SYS chassis in a 4-post rack.

•

Rack Mount the NCS-57C3-MOD Chassis in a 4-Post Rack using Sliders, on page 41

— Contains the

procedure for mounting the NCS-57C3-MOD-S and NCS-57C3-MOD-SE-S chassis in a 4-post rack
using a sliders.

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Install the Chassis

Rack Mount the Chassis

Summary of Contents for NCS 5700 Series
























































































































Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands

Cisco NCS 5700 Series, Hardware Installation Manual

Search results

Summary of Contents for NCS 5700 Series

Reviews:

Related manuals for NCS 5700 Series

Brands by name

Popular brands