Cisco ME-3600X-24CX Series Manual Download Page 55 | Manualshive

Page: 55 / 63

background image

5-2

Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide

OL-27620-01

Chapter 5 Configuring Pseudowire

Pseudowire Overview

In the SAToP mode the interface is considered as a continuous framed bit stream. The packetization of
the stream is done according to IETF RFC 4553. All signaling is carried out transparently as a part of a
bit stream.

Figure 5-1

shows the frame format in Unstructured SAToP mode.

Figure 5-1

Unstructured Mode Frame Format

Table 5-1

shows the payload and jitter limits for the T1 lines in the SAToP frame format.

Table 5-1

SAToP T1 Frame: Payload and Jitter Limits

Table 5-2

shows the payload and jitter limits for the E1 lines in the SAToP frame format.

Table 5-2

SAToP E1 Frame: Payload and Jitter Limits

For instructions on how to configure SAToP, see

Configuring Structure-Agnostic TDM over Packet

(SAToP)

.

Circuit Emulation Service over Packet-Switched Network

CESoPSN encapsulates structured (NxDS0) TDM signals as PWs over public switched networks
(PSNs). It complements similar work for structure-agnostic emulation of TDM bit streams, such as
SAToP. Emulation of NxDS0 circuits saves PSN bandwidth and supports DS0-level grooming and
distributed cross-connect applications. It also enhances resilience of CE devices due to the effects of loss
of packets in the PSN.

CESoPSN identifies framing and sends only the payload, which can either be channelized T1s within
DS3 or DS0s within T1. DS0s can be bundled to the same packet. The CESoPSN mode is based on IETF
RFC 5086.

CESoPSN supports channel-associated signaling (CAS) for E1 and T1 interfaces. CAS provides
signaling information within each DS0 channel as opposed to using a separate signaling channel. CAS
also referred to as in-band signaling or robbed bit signaling.

Encapsulation header

CE Control (4Bytes)

RTP (optional 12B)

Bytes 1-N

CEoP

Payload

230547

Maximum
Payload

Maximum
Jitter

Minimum
Jitter

Minimum
Payload

Maximum
Jitter

Minimum
Jitter

960

320

10

192

64

2

Maximum
Payload

Maximum
Jitter

Minimum
Jitter

Minimum
Payload

Maximum
Jitter

Minimum
Jitter

1280

320

10

256

64

2

«
...
53
54
55
56
57
...
»

Summary of Contents for ME-3600X-24CX Series
































































Reviews:

No comments

Related manuals for ME-3600X-24CX Series

Brand: FANATEC Pages: 40

Brand: IDEC Pages: 8

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: Eaton Pages: 4

Brand: hager Pages: 2

Brand: Open Mesh Pages: 2

Sierra Pro XL 1608V5S

Brand: Kramer Pages: 2

Brand: Homefibre Pages: 2

IES6200-PN-16T4GS-2P48

Brand: 3onedata Pages: 3

Brand: nedis Pages: 24

Brand: Kramer Pages: 11

Brand: Leaksafe Solutions Pages: 12

EXT-HDMI-CAT5-844

Brand: Gefen Pages: 28

CT.TS005.501401

Brand: Talkswitch Pages: 9

Brand: A-Neuvideo Pages: 9

Brand: Zektor Pages: 30

Brand: Gefen Pages: 12

Brand: GORMAN-RUPP PUMPS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands