Cisco ME-3600X-24CX Series Manual Download Page 50

Page: 50 / 63

4-11

Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide

OL-27620-01

Chapter 4 Configuring Clocking and Timing

Clocking Sample Configurations

Configuring an External Clock Source

To configure an external clock source using Synchronous Ethernet, use the network-clock input-source
priority external 1/0/0 {{E1 {crc4 | cas |fas}} {T1 {d4 | sf | esf}} } command.

Switch(config)# network-clock input-source 1 external 1/0/0

Configuring Synchronous Ethernet ESMC and SSM

For instructions on how to configure synchronous Ethernet Synchronization Message Channel
(ESMC)and Synchronization Status Message (SSM), see

Configuring Synchronous Ethernet

in Cisco

ME 3800x and ME 3600x Switch Software Configuration Guide

Verifying Clock-Related Settings

Use the following commands to verify the clock settings:

•

show ptp clock dataset

•

show ptp port dataset

•

show ptp clock running

•

show platform ptp all

For more information about these commands, see the

Cisco ME 3800X and ME 3600X Switch Command

Reference, Release 15.2(4)S

Clocking Sample Configurations

The following sections show a sample configurations for clocking features on the switch.

Ordinary Clock—Slave

ptp clock ordinary domain 0

clock-port Slave slave

transport ipv4 unicast interface loopback 0 negotiation

clock-source 8.8.8.1

sync interval 1

announce timeout 7

delay-req interval 3

Ordinary Clock—Master

ptp clock ordinary domain 0

clock-port Master master

transport ipv4 unicast interface loopback 0 negotiation

Unicast Configuration—Slave Mode

ptp clock ordinary domain 0

clock-port Slave slave

transport ipv4 unicast interface loopback 0

clock-source 8.8.8.1

Summary of Contents for ME-3600X-24CX Series
































































Search results

Summary of Contents for ME-3600X-24CX Series

Reviews:

Related manuals for ME-3600X-24CX Series

Brands by name

Popular brands

Cisco ME-3600X-24CX Series, Manual

Search results

Summary of Contents for ME-3600X-24CX Series

Reviews:

Related manuals for ME-3600X-24CX Series

Brands by name

Popular brands