Cisco ME-3600X-24CX Series Manual Download Page 49

Page: 49 / 63

4-10

Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide

OL-27620-01

Chapter 4 Configuring Clocking and Timing

Configuring Clocking and Timing

Master:

Switch(config)#ptp clock ordinary domain 0

Switch(config-ptp-clk)#input 1pps 0/0

Switch(config-ptp-clk)#tod 0/0 ?

cisco Set TOD format to CISCO

nmea Set TOD format to NMEA ZDA

ntp Set TOD format to NTP

ubx Set TOD format to UBX

Slave:

Switch(config)#ptp clock ordinary domain 0

Switch(config-ptp-clk)#output 1pps 0/0 ?

offset 1PPS output offset

pulse-width 1PPS output pulse width

Switch(config-ptp-clk)#tod 0/0 ?

cisco Set TOD format to CISCO

nmea Set TOD format to NMEA ZDA

ntp Set TOD format to NTP

ubx Set TOD format to UBX

Note

To see further configuration examples for input and output timing, see

Clocking Sample Configurations

Configuring a Transparent Clock

Follow these steps to configure the Cisco ME 3600X 24CX Series Switch as an end-to-end transparent
clock.

Note

The Cisco ME 3600X 24CX Series Switch does not support peer-to-peer transparent clock mode.

Configuring Synchronous Ethernet

The following sections describe how to configure synchronous Ethernet timing on the Cisco ME 3600X
24CX Series Switch switch.

Note

Hybrid mode is not supported therefore, network-clock input-source command cannot be configured
with Ordinary Slave mode or Boundary Clock mode.

Command

Purpose

Step 1

Router# configure terminal

Enter configuration mode.

Step 2

ptp clock {ordinary | boundary |
e2e-transparent} domain
domain-number [hybrid]

Configures the router as an end-to-end transparent clock.

Note

Peer-to-peer transparent clock mode is not
supported.

Step 3

Router(config)# end

Exit configuration mode.

Summary of Contents for ME-3600X-24CX Series
































































Search results

Summary of Contents for ME-3600X-24CX Series

Reviews:

Related manuals for ME-3600X-24CX Series

Brands by name

Popular brands

Cisco ME-3600X-24CX Series, Manual

Search results

Summary of Contents for ME-3600X-24CX Series

Reviews:

Related manuals for ME-3600X-24CX Series

Brands by name

Popular brands