Cisco ME-3600X-24CX Series Manual Download Page 20 | Manualshive

Page: 20 / 63

background image

C H A P T E R

2-1

Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide

OL-27620-01

2

Configuring T1/E1 Interfaces

This chapter provides information about configuring the T1/E1 interface module on the Cisco ME
3600X 24CX Series Switch. It includes the following sections:

•

Required Configuration Tasks, page 2-1

•

Optional Configuration Tasks, page 2-5

•

Saving the Configuration, page 2-9

•

Troubleshooting E1 and T1 Controllers, page 2-9

•

Monitoring and Maintaining the T1/E1 Interface Module, page 2-13

•

Configuring CEM, page 2-13

•

Configuration Examples, page 2-16

For information about managing your system images and configuration files, refer to the Cisco IOS
Configuration Fundamentals Configuration Guide and Cisco IOS Configuration Fundamentals
Command Reference publications.

For more information about the commands used in this chapter, refer to the Cisco IOS Command
Reference publication for your Cisco IOS software release.

Software Limitation

When configuring the T1/E1 interface module on the Cisco ME 3600X 24CX Series Switch, only the
following BERT patterns are currently supported: 2^11, 2^15, 2^20-O153, and 2^20-QRSS.

Required Configuration Tasks

This section lists the required configuration steps to configure the T1/E1 interface module. Some of the
required configuration commands implement default values that might be appropriate for your network.
If the default value is correct for your network, then you do not need to configure the command.

•

Setting the Card Type, page 2-2

•

Enabling the Interfaces on the Controller, page 2-2

•

Setting the IP Address, page 2-4

«
...
18
19
20
21
22
...
»

Summary of Contents for ME-3600X-24CX Series
































































Reviews:

No comments

Related manuals for ME-3600X-24CX Series

Brand: Omega Engineering Pages: 3

Brand: Zektor Pages: 65

Brand: REV Ritter Pages: 15

Brand: Metrix Pages: 12

Brand: Xcellon Pages: 2

Brand: TRENDnet Pages: 2

Brand: N-Tron Pages: 15

Brand: CoolGear Pages: 8

Brand: MaxTech Pages: 10

XS-S1920 Series

Brand: Ruijie Pages: 51

OmniView F1D066

Brand: Belkin Pages: 12

Brand: N-Tron Pages: 2

Brand: QNAP Pages: 48

SuperStack II Switch 3300

Brand: 3Com Pages: 64

Brand: ABB Pages: 9

Brand: ITC Audio Pages: 12

Brand: Dahua Pages: 124

Brand: CYP Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands