Cisco Internet Router Cisco 12404 Installation And Configuration Manual Download Page 33 | Manualshive

Page: 33 / 292

background image

1-9

Cisco 12404 Internet Router Installation and Configuration Guide

OL-11636-01

Chapter 1 Product Overview

Route Processors

NVRAM

Non-Volatile Random Access Memory (NVRAM) cannot be upgraded or
configured. The system configuration, software configuration register settings,
and environmental monitoring logs are contained in the 512-KB NVRAM, which
is backed up with built-in lithium batteries that retain the contents for a minimum
of five years.

Caution

Before you replace the RP in the system, back up the running configuration to a
Trivial File Transfer Protocol (TFTP) file server or an installed Flash memory
card so you can retrieve it later.

Flash Memory or SIMM

A single inline memory module (SIMM) is a Flash memory card that allows you
to remotely load and store multiple Cisco IOS software and microcode images.
You can download a new image over the network or from a local server and then
add the new image to Flash memory or replace the existing files. You can then
boot the routers either manually or automatically from any of the stored images.
Flash memory also functions as a trivial file transfer protocol (TFTP) server to
allow other servers to boot remotely from stored images or to copy them into their
own Flash memory.

Read Only Memory

Read-only memory (ROM), computer memory on which data has been
prerecorded. Once data has been written onto a ROM chip, it cannot be removed
and can only be read.

Unlike main memory (RAM), ROM retains its contents even when the computer
is turned off. ROM is referred to as being nonvolatile, whereas RAM is volatile.

The GRP provides two dedicated PCMCIA card slots. Either

slot can support a

Flash memory card or an input/output (I/O) device, as long as the device requires
only +5 VDC. The GRP supports Type 1 and Type 2 devices. Each PCMCIA slot
has an ejector button for ejecting the card from its slot.

todd.book Page 9 Tuesday, November 27, 2007 6:02 PM

«
...
31
32
33
34
35
...
»

Summary of Contents for Internet Router Cisco 12404





































































































































































































































































































Reviews:

No comments

Related manuals for Internet Router Cisco 12404

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: DPtech Pages: 39

Brand: KPN Pages: 14

Brand: bintec elmeg Pages: 33

PCH1 T P Series

Brand: Parker Pages: 107

Brand: Idis Pages: 17

IGS-5225-20T4C2X

Brand: Planet Pages: 16

Brand: MSNswitch Pages: 2

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Q-SYS QIO-GP8x8

Brand: QSC Pages: 13

Brand: Transition Networks Pages: 5

CANopen Communication Module DVPCP02-H2

Brand: Delta Electronics Pages: 2

Brand: TRENDnet Pages: 3

WNR2000v2 - Wireless- N 300 Router

Brand: NETGEAR Pages: 144

BladeCenter 1/10 Gb Uplink Ethernet SwitchModule

Brand: IBM Pages: 58

IPSec VPN Client Zyxel ZyWall 10

Brand: TheGreenBow Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands