Cisco Firepower 9300 Hardware Installation Manual Download Page 76 | Manualshive

Page: 76 / 80

background image

Figure 52: Connect the DC Power Connectors and Ground Lugs

Nuts

2

DC terminal covers

1

DC terminals

4

Two 2-hole lugs (not provided in accessory
kit)

3

Chassis ground lug

5

Step 7

Connect the DC-input wires to the power entry module terminal block. The proper wiring sequence is positive to positive
(red wire) and negative to negative (black wire).

Step 8

Replace the terminal covers as shown in the figure above.

This cover should always be in place when power is applied to the terminals.

Step 9

Set the DC disconnect switch in the circuit to ON.

In a system with multiple power supplies, connect each power supply to a separate DC power source. In the
event of a power source failure, if the second source is still available, it can maintain system operation.

Caution

Step 10

Verify power supply operation by checking the power supply LED on the front of the chassis.

See

Power Supply Modules, on page 24

for the LED values.

Connect the HVDC Power Supply Module

Take note of the following warnings:

Cisco Firepower 9300 Hardware Installation Guide

72

Maintenance and Upgrade

Connect the HVDC Power Supply Module

«
...
74
75
76
77
78
...
»

Summary of Contents for Firepower 9300

















































































Reviews:

No comments

Related manuals for Firepower 9300

Brand: SonicWALL Pages: 21

Brand: Juniper Pages: 483

Brand: Barracuda Pages: 8

Brand: H3C Pages: 90

Brand: Check Point Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands