manualshive.com logo in svg

Cisco Firepower 9300, Hardware Installation Manual, Page: 28 / 80

Share
Download
Cisco Firepower 9300 Hardware Installation Manual Download Page 28

Cable distance

Half the
distance
specified by
the IEEE
standard.

Note

Modal bandwidth
(MHz/km

Core diameter (microns)

5 km

Single mode

G.652

Cable and operating
distance

Power Supply Modules

The Firepower 9300 supports two AC, two DC, or two high-voltage DC (HVDC) power supply modules so
that dual power supply redundancy protection is available. Facing the front of the chassis, the power supply
modules are numbered left to right, for example, PSU-1 and PSU-2.

Make sure that one power supply module is always active.

Attention

AC Power Supply Modules

The 220-V power supply modules run at 2500 W for 200 to 240 V AC. The load is shared when both
power supply modules are plugged in and running at the same time. The power supply modules support
hot swapping. The power supply entry module is not removable. This is the module that you plug the
power cords into.

After removing power from the chassis either by moving the power switch to OFF or unplugging the
power cord, wait at least 10 seconds before turning power back ON.

Note

Table 6: AC Power Supply LEDs

Amber LED

Green LED

Power Switch Position

Off

Off

On

No input AC power

Off

Off

Off

On

Off

On

Power supply failure

Flashing

Power supply
warning, must be
reset by the system

Off

Off

Cisco Firepower 9300 Hardware Installation Guide

24

Overview

Power Supply Modules

Summary of Contents for Firepower 9300

















































































Reviews:

No comments