Cisco Firepower 9300 Hardware Installation Manual Download Page 25

Page: 25 / 80

Figure 14: FPR9K-NM-2X40G-F

Ethernet

Ports 1 and 2 are paired together to form
a hardware bypass pair.

Captive screw/handle

Ethernet

Ports 1 and 2 are paired together to form
a hardware bypass pair.

Bypass LED BP:

• Green—In standby mode.

• Amber, flashing—Port is in hardware

bypass mode, failure event.

• Amber—Port is in hardware bypass

mode, forced.

Network activity LEDs:

• Amber—No connection, or port is

not in use, or no link or network
failure.

• Green—Link up, no network activity.

• Green, flashing—Network activity.

The following table describes the cable specifications needed to keep the insertion loss as low as possible.

Table 2: 40-G BASE-SR Cable Specifications

Supported Cable

Interface

50 microns core diameter

Ethernet 40-G BASE-SR4

2000/4700 (OM3/4) modal bandwidth (MHz*km)

850 nm wavelength

50 m cable distance

MPO-12 port adapter

Cisco Firepower 9300 Hardware Installation Guide

Overview

40-G Network Module with Hardware Bypass

Summary of Contents for Firepower 9300

















































































Search results

Summary of Contents for Firepower 9300

Reviews:

Cisco Firepower 9300, Hardware Installation Manual, Page: 25 / 80

Search results

Summary of Contents for Firepower 9300

Reviews: