Cisco Firepower 9300 Hardware Installation Manual Download Page 13

Page: 13 / 80

Security module 1

Security module 3

1 Gigabit Ethernet management port

RJ-45 console port

Eight 10 Gigabit Ethernet data ports
(Gigabit Ethernet 1/1 through 1/8)

2.0 USB port

Network module 1

Supervisor

Security module 2

Network module 2

Power supply module PSU-1

Power supply module PSU-2

For More Information

• See

Chassis Components, on page 4

for a list of all of the chassis components.

• See

Supervisor, on page 10

for detailed information about the Supervisor.

• See

Security Modules, on page 12

for detailed information about the security modules.

• See

Network Modules, on page 14

for detailed information about the network modules.

• See

Hardware Bypass Network Modules, on page 19

for detailed information about fail-to-wire

network modules

• See

Power Supply Modules, on page 24

for detailed information about the power supply modules.

Rear Panel

The following figure shows the rear panel of the Firepower 9300.

Figure 6: Firepower 9300 Rear Panel

Power feed for PSU-1

Power feed for PSU-2

Fan module FAN-1

On/Off switch

Cisco Firepower 9300 Hardware Installation Guide

Overview

Rear Panel

Summary of Contents for Firepower 9300

















































































Search results

Summary of Contents for Firepower 9300

Reviews:

Cisco Firepower 9300, Hardware Installation Manual, Page: 13 / 80

Search results

Summary of Contents for Firepower 9300

Reviews: