Cisco Firepower 9300 Hardware Installation Manual Download Page 6

Page: 6 / 80

The Firepower 9300 is certified for Common Criteria (CC) and Federal Information Processing Standards
(FIPS). See "

Security Certifications Compliance

" in the

Cisco FXOS CLI Configuration Guide

for the procedure

for enabling these modes using the CLI. See "

Security Certifications Compliance

" in the

Cisco FXOS Firepower

Chassis Manager Configuration Guide

for information for enabling these modes using the Firepower Chassis

Manager.

Note

The following figure shows a fully populated Firepower 9300.

Figure 1: Firepower 9300

See the

Cisco Interactive Library

for a video that displays the features and components of the Firepower 9300.

The following table lists the hardware features of the Firepower 9300.

Table 1: Firepower 9300 Features

Description

Feature

3 RU

Form factor

Yes

Mount rails included (4-post EIA-310-D rack) with span between front and rear rails
of 24 to 36 in.

Rack mount

Front to rear

Cold aisle to hot aisle

Airflow

Cisco Firepower 9000 Supervisor with eight 10-Gigabit Ethernet ports and 2 network
module slots for I/O expansion

Supervisor

Security module
slots

Located in the Supervisor

Network module
slots

Cisco Firepower 9300 Hardware Installation Guide

Overview

Features

Summary of Contents for Firepower 9300

















































































Search results

Summary of Contents for Firepower 9300

Reviews:

Brands by name

Popular brands

Cisco Firepower 9300, Hardware Installation Manual

Search results

Summary of Contents for Firepower 9300

Reviews:

Brands by name

Popular brands