manualshive.com logo in svg

Cisco Catalyst 6509, Software Manual

The Cisco Catalyst 6509 is a highly efficient networking device designed for enterprise-level connectivity and scalability. To maximize its potential, you can easily obtain the comprehensive "Power Manual" from our website, where you can download the manual for free. Explore the full capabilities of this remarkable device at manualshive.com.

Share
Download
background image

 

11-8

Catalyst 6500 Series Switch Software Configuration Guide—Release 8.7

OL-8978-04

Chapter 11      Configuring VLANs

Mapping VLANs to VLANs

This example shows how to enable MAC address reduction and create an extended-range Ethernet 
VLAN:

Console> (enable) 

set spantree macreduction enable

MAC address reduction enabled

Console> (enable) 

set vlan 2000 

Vlan 2000 configuration successful

Console> (enable) 

show vlan 2000

VLAN Name                             Status    IfIndex Mod/Ports, Vlans

---- -------------------------------- --------- ------- ------------------------

2000 VLAN2000                         active    61

VLAN Type  SAID       MTU   Parent RingNo BrdgNo Stp  BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ ------ ---- -------- ------ ------

2000 enet  102000     1500  -      -      -      -    -        0      0

VLAN Inst DynCreated  RSPAN

---- ---- ---------- --------

2000 -    static     disabled

Console> (enable)

This example shows how to display a summary of active, suspended, and extended VLANs:

Console> (enable) 

show vlan summary

Vlan status    Count  Vlans

-------------  --------------------------------------------------------

VTP Active       504   1-100,102-500,1000,1002-1005

 

VTP Suspended      1   101

 

Extended           1   2000

Console> (enable)

Mapping VLANs to VLANs

Note

To configure the VLAN mappings on a per-port or per-ASIC basis, see the 

“Configuring VLAN 

Mappings on a Per-Port or Per-ASIC Basis” section on page 11-14

.

Note

With software release 8.3(1) and later releases, the global VLAN mapping feature is not needed because 
ISL trunks now support the entire VLAN range (1 to 4094).

You can map the VLANs from the 802.1Q trunks that are connected to the VLANs on the non-Cisco 
devices to the ISL trunks that are connected to the other VLANs on the Catalyst 6500 series switches.

Note

If you map the 802.1Q VLANs to the ISL VLANs, you can retain the mappings from a previous 
Catalyst 6500 series software release but you cannot use the extended-range VLANs.

This section describes how to map the VLANs to VLANs:

•

Mapping 802.1Q VLANs to ISL VLANs, page 11-9

•

Deleting 802.1Q-to-ISL VLAN Mappings, page 11-10

Summary of Contents for Catalyst 6509

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 6509

LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
National Instruments Module NI PXI-8250 User Manual preview
Module NI PXI-8250
Brand: National Instruments Pages: 39
Paradox ZX32D Manual preview
ZX32D
Brand: Paradox Pages: 4
XAVI Technologies Corp. 7721r User Manual preview
7721r
Brand: XAVI Technologies Corp. Pages: 71
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Freescale Semiconductor FRDM-STBC-SA9500 Quick Reference Card preview
FRDM-STBC-SA9500
Brand: Freescale Semiconductor Pages: 2
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Baicells EG2013B-M11 User Manual preview
EG2013B-M11
Brand: Baicells Pages: 10
HPE FlexNetwork 5130 Series Troubleshooting Manual preview
FlexNetwork 5130 Series
Brand: HPE Pages: 33
RANA Systems RanaSystems 13-0010--001 User Manual preview
RanaSystems 13-0010--001
Brand: RANA Systems Pages: 328
SYNTEK STA-UI-A0035 User Manual preview
STA-UI-A0035
Brand: SYNTEK Pages: 41
ORiNG PCard-E 021L-D5 Series Quick Installation Manual preview
PCard-E 021L-D5 Series
Brand: ORiNG Pages: 2
Razer RZ37-0251 Manual preview
RZ37-0251
Brand: Razer Pages: 17
Topcom Xplorer 871B (Norwegian) Hurtig Installasjonsveiledning preview
Xplorer 871B
Brand: Topcom Pages: 16
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Brand: swiftech Pages: 2
M-system M5XSBS Instruction Manual preview
M5XSBS
Brand: M-system Pages: 4

Brands by name

Popular brands

Load more brands