manualshive.com logo in svg

Cisco ASR 920 series, Configuration Manual Ethernet Router

Introducing the Cisco ASR 920 series, a cutting-edge networking solution for seamless connectivity. Unlock the full potential of this powerful device with our comprehensive Configuration Manual available for free download at manualshive.com. Equip yourself with essential user insights and optimize performance effortlessly.

Share
Download
background image

•

Down (toward the wire) MEPs.

A domain can be removed when all maintenance points within the domain have been removed and all remote
MEP entries in the continuity check database (CCDB) for the domain have been purged.

Maintenance Points

A maintenance point (MIP) is a demarcation point on an interface or port that participates in Connectivity
Fault Management (CFM) within a maintenance domain. Maintenance points on device ports act as filters
that confine CFM frames within the bounds of a domain by dropping frames that do not belong to the correct
level. Maintenance points must be explicitly configured on Cisco devices. Two classes of maintenance points
exist, maintenance end points (MEPs) and MIPs. Support for MIPs varies by Cisco release.

Maintenance Association Endpoints

Maintenance association endpoints (MEPs) reside at the edge of a maintenance domain and confine Ethernet
Connectivity Fault Management (CFM) messages within the domain via the maintenance domain level. MEPs
periodically transmit and receive continuity check messages (CCMs) from other MEPs within the domain.
At the request of an administrator, linktrace and loopback messages can also be transmitted. MEPs are either

“

Up

”

(toward the bridge) or

“

Down

”

(toward the wire). Support for Up MEPs varies by Cisco release.

When the

continuity-check static rmep

command is configured on a port MEP and continuity checking does

not detect a removed MEP, the port is set to MAC operation down and the interface protocol is set to down.
Normal traffic is stopped because the line protocol is down, but CFM packets still pass.

MEP configurations can be removed after all pending loopback and traceroute replies are removed and the
service on the interface is set to transparent mode.

Down MEPs for Routed Ports

Down MEPs communicate through the wire.

Down MEPs use the port MAC address.

A Down MEP performs the following functions:

•

Sends and receives Ethernet CFM frames at its level via the wire connected to the port where the MEP
is configured.

•

Processes all Ethernet CFM frames at its level coming from the direction of the wire.

•

Drops all Ethernet CFM frames at a lower level coming from the direction of the wire.

•

Transparently drops all Ethernet CFM frames at a higher level, independent of whether they came in
from the bridge or wire.

Ethernet CFM Messages

Ethernet CFM uses standard Ethernet frames. Ethernet CFM frames are distinguishable by EtherType and for
multicast messages by MAC address. Ethernet CFM frames are sourced, terminated, processed, and relayed
by bridges. Routers can support only limited Ethernet CFM functions.

   Carrier Ethernet Configuration Guide (Cisco ASR 920 Series)

250

Configuring Ethernet CFM

Maintenance Points

Summary of Contents for ASR 920 series























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 920 series

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems SmartSTACK ELS100-24TXG Installation And User Manual preview
SmartSTACK ELS100-24TXG
Brand: Cabletron Systems Pages: 112
Cabletron Systems ESX-1380 Management Manual preview
ESX-1380
Brand: Cabletron Systems Pages: 86
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems CSX200 CyberSWITCH Setup Manual preview
CSX200 CyberSWITCH
Brand: Cabletron Systems Pages: 2
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
Patton electronics 1018RC User Manual preview
1018RC
Brand: Patton electronics Pages: 12
NETGEAR RP614 v2 Installation Manual preview
RP614 v2
Brand: NETGEAR Pages: 2
ProCurve J8454A Quick Start Manual preview
J8454A
Brand: ProCurve Pages: 2
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
Sun Microsystems McDATA Eclipse 1620 Release Notes preview
McDATA Eclipse 1620
Brand: Sun Microsystems Pages: 9
3Com 3C13755-US - Router 5642 Installation Manual preview
3C13755-US - Router 5642
Brand: 3Com Pages: 104

Brands by name

Popular brands

Load more brands