Cisco aironet 1130 Design And Deployment Manual Download Page 65 | Manualshive

Page: 65 / 184

background image

65

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

c.

Click the

High Availability

tab. (See

.)

Figure 42

All APs > Details for (High Availability) Window

d.

If desired, enter the name and IP address of the primary backup controller for this access point in
the Primary Controller fields.

Note

Entering an IP address for the backup controller is optional in this step and the next two
steps. If the backup controller is outside the mobility group to which the mesh access point
is connected (the primary controller), then you need to provide the IP address of the primary,
secondary, or tertiary controller, respectively. The controller name and IP address must
belong to the same primary, secondary, or tertiary controller. Otherwise, the mesh access
point cannot join the backup controller.

e.

If desired, enter the name and IP address of the secondary backup controller for this mesh access
point in the Secondary Controller fields.

f.

If desired, enter the name and IP address of the tertiary backup controller for this mesh access point
in the Tertiary Controller fields.

g.

No change is required to the AP Failover Priority value. The default value for mesh access points is

critical

and it cannot be modified.

h.

Click

Apply

to commit your changes.

Step 7

Click

Save Configuration

to save your changes.

Using the CLI to Configure Backup Controllers

Using the controller CLI, follow these steps to configure primary, secondary, and tertiary controllers for
a specific mesh access point and to configure primary and secondary backup controllers for all mesh
access points.

Step 1

To configure a primary controller for a specific mesh access point, enter this command:

config ap primary-base

controller_name Cisco_AP

[

controller_ip_address

]

«
...
63
64
65
66
67
...
»

Summary of Contents for aironet 1130

























































































































































































Reviews:

No comments

Related manuals for aironet 1130

Brand: D-Link Pages: 11

Brand: D-Link Pages: 83

Brand: D-Link Pages: 129

Brand: D-Link Pages: 10

Brand: D-Link Pages: 21

Brand: D-Link Pages: 6

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 6

Brand: D-Link Pages: 86

Brand: D-Link Pages: 3

Brand: D-Link Pages: 4

Brand: D-Link Pages: 4

DSL-3580L Series

Brand: D-Link Pages: 20

Brand: D-Link Pages: 64

Brand: D-Link Pages: 73

Brand: 4IPNET Pages: 97

Brand: LAWO Pages: 154

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands