Cisco aironet 1130 Design And Deployment Manual Download Page 50 | Manualshive

Page: 50 / 184

background image

50

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Site Preparation and Planning

Figure 33

Cell Radius of 1000 Feet and Access Point Placement for Voice Mesh Networks

Note

Refer to

“Guidelines For Using Voice On The Mesh Network” section on page 112

for additional

voice considerations when configuring voice on your network.

Wireless Propagation Characteristics

provides a comparison of the 2.4 GHz and 5 GHz bands.

The 2.4 GHz band does provide better propagation characteristics than 5 GHz, but 2.4 GHz is an
unlicensed band and has historically been affected with more noise and interference to date than the
5 GHz band. In addition, because there are only three backhaul channels in 2.4 GHz, co-channel
interference would result. Therefore, the best method to achieve comparable capacity is by reducing
system gain (that is, transmit power, antenna gain, receive sensitivity, and path loss) to create smaller
cells. Keep in mind that these smaller cells require more access points per square mile (greater access
point density).

Therefore, 2.4GHz has more penetration capability across the obstacles due to larger wavelength. In
addition, 2.4 GHz has lower date rates which increases the success of the signal to reach the other end.

Table 11

Comparison of 2.4-GHz and 5-GHz Bands

2.4 GHz Band Characteristics

5 GHz Band Characteristics

3 channels

20 channels

More prone to co-channel interference

No co-channel interference

Lower power

Higher power

Data rates less than 6 Mb/s

Data rates 6 Mb/s and greater (up to 54 Mb/s).

Lower SNR requirements given lower data rates

Higher SNR requirements given higher data rates

Better propagation characteristics than 5 GHz but
more susceptible to noise and interference

Worse propagation characteristics than 2.4 GHz
but less susceptible to noise and interference

Unlicensed band. Widely available throughout the
world.

Not as widely available in the world as 2.4-GHz.
Licenses in some countries.

«
...
48
49
50
51
52
...
»

Summary of Contents for aironet 1130

























































































































































































Reviews:

No comments

Related manuals for aironet 1130

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: NXP Semiconductors Pages: 24

Brand: Compaq Pages: 112

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: CAP-XX Pages: 8

Brand: Uniden Pages: 5

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

Brand: Konica Minolta Pages: 31

ADSL Ethernet & USB Combo Router Lynx L-510

Brand: Starbridge Networks Pages: 59

Brand: Handicare Pages: 60

Brand: Zalip Pages: 76

Brand: ZyXEL Communications Pages: 2

Brand: Renesas Pages: 67

Brand: EMC Pages: 88

Brand: ZyXEL Communications Pages: 191

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands