Cisco aironet 1130 Design And Deployment Manual Download Page 172 | Manualshive

Page: 172 / 184

background image

172

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Adding and Managing Mesh Access Points with Cisco WCS

Note

The Mesh Statistics tab and its subordinate tabs (Bridging, Queue and Security) only appear for
mesh access points. The Mesh Link Alarms and Mesh Link Events links are accessible from each
of the three tabbed panels.

Note

You can also access the Mesh Securities panel for a mesh access point from a Cisco WCS map.
To display the panel, click the arrow portion of the mesh access point label.

Figure 104

Monitor > Access Points > AP Name > Mesh Statistics

Summaries of the Bridging, Queue and Security Statistics and their definitions are provided in

,

and

respectively.

Table 25

Bridging Mesh Statistics

Parameter

Description

Role

The role of the mesh access point. Options are
mesh access point (MAP) and root access point
(RAP).

Bridge Group Name (BGN)

The name of the bridge group to which the MAP
or RAP is a member. Assigning membership in a
BGN is recommended. If one is not assigned, a
MAP is by default assigned to a default BGN.

Backhaul Interface

The radio backhaul for the mesh access point.

«
...
170
171
172
173
174
...
»

Summary of Contents for aironet 1130

























































































































































































Reviews:

No comments

Related manuals for aironet 1130

Brand: D-Link Pages: 99

Brand: D-Link Pages: 5

Brand: D-Link Pages: 15

AirPro DWL-6000AP

Brand: D-Link Pages: 65

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: FabiaTech Pages: 4

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands