Cisco aironet 1130 Design And Deployment Manual Download Page 110 | Manualshive

Page: 110 / 184

background image

110

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Figure 71

Controller to RAP Path

For CAPWAP control traffic the IP DSCP value is set to 46, and the 802.1p user priority is set to 7. Prior
to transmission of a wireless frame over the backhaul, regardless of node pairing (RAP/MAP) or
direction, the DSCP value in the outer header is used to determine a backhaul priority. The following
sections describe the mapping between the four backhaul queues the mesh access point uses and the
DSCP values shown in Backhaul Path QoS (

).

Note

The platinum backhaul queue is reserved for CAPWAP control traffic, IP control traffic, and voice
packets. DHCP, DNS and ARP requests are also transmitted at the platinum QoS level. The mesh
software inspects each frame to determine whether it is an CAPWAP control or IP control frame in order
to protect the platinum queue from use by non-CAPWAP applications.

For a MAP to the client path, there are two different procedures, depending on whether the client is a
WMM client or a normal client. If the client is a WMM client, the DSCP value in the outer frame is
examined, and the 802.11e priority queue is used (

).

If the client is not a WMM client, the WLAN override (as configured at the controller) determines the
802.11e queue (bronze, gold, platinum, or silver), on which the packet is transmitted.

For client towards mesh access point, there are modifications made to incoming client frames in
preparation for transmission on the mesh backhaul or Ethernet. For WMM clients, MAP illustrates the
way in which the outer DSCP value is set from an incoming WMM client frame.

205688

802.1p UP O

u

ter IP DSCP O

u

ter

CAPWAP

Encaps

u

lation

Incoming 802.1p UP IP DSCP Inner

Table 16

Backhaul Path QoS

DSCP Value

Backhaul Queue

2, 4, 6, 8 to 23

Bronze

26, 32 to 63

Gold

46 to 56

Platinum

All others including 0

Silver

Table 17

MAP to Client Path QoS

DSCP Value

Backhaul Queue

2, 4, 6, 8 to 23

Bronze

26, 32 to 45, 47

Gold

46, 48 to 63

Platinum

All others including 0

Silver

«
...
108
109
110
111
112
...
»

Summary of Contents for aironet 1130

























































































































































































Reviews:

No comments

Related manuals for aironet 1130

Brand: ZALMAN Pages: 20

Brand: CAME Pages: 19

Brand: Dahua Pages: 6

TOWERCHRON DP72

Brand: Grasslin Pages: 2

Brand: Alesis Pages: 46

RUGGEDSWITCH RS900G

Brand: RuggedCom Pages: 23

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

SteelCentral NetExpress

Brand: Riverbed Pages: 38

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

DSL5068EN(1T1R)

Brand: Aztech Pages: 40

Power Control Processor

Brand: ETC Pages: 64

Core 2 Quad Q9400

Brand: Intel Pages: 2

Brand: NETGEAR Pages: 2

Brand: Perle Pages: 2

InvenSense RoboKit1

Brand: TDK Pages: 13

Brand: ACTi Pages: 12

DotSurfer GPC-2100

Brand: Gtran Wireless Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands