Cisco 7941G - Unified IP Phone VoIP Administration Manual Download Page 166

Page: 166 / 302

Chapter 5 Configuring Features, Templates, Services, and Users

Telephony Features Available for the Cisco Unified IP Phone

5-18

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

Music-on- hold

Plays music while callers are on hold.

For more information refer to:

•

Cisco Unified
Communications Manager
Administration Guide

, “Music

On Hold Audio Source
Configuration” and “Music On
Hold Server Configuration”
chapters.

•

Cisco Unified
Communications Manager
System Guide

, “Music on

Hold” chapter.

•

Cisco Unified
Communications Manager
Features and Services Guide

“Music On Hold” chapter.

Onhook call
transfer

Allows a user to press a single Transfer
softkey and then go onhook to complete a
call transfer.

For more information refer to

Cisco Unified Communications
Manager System Guide, “

Cisco

Unified IP Phones” chapter.

Other group pickup Allows a user to answer a call ringing on a

phone in another group that is associated
with the user's group.

For more information refer to:

•

Cisco Unified
Communications Manager
Administration Guide

“Pickup Group Configuration”
chapter.

•

Cisco Unified
Communications Manager
System Guide, “

Call Pickup

Group” chapter.

Table 5-1

Telephony Features for the Cisco Unified IP Phone (continued)

Feature

Description Configuration

Reference

Summary of Contents for 7941G - Unified IP Phone VoIP















































































































































































































































































































Search results

Summary of Contents for 7941G - Unified IP Phone VoIP

Reviews:

Related manuals for 7941G - Unified IP Phone VoIP

Brands by name

Popular brands

Cisco 7941G - Unified IP Phone VoIP, Administration Manual

Search results

Summary of Contents for 7941G - Unified IP Phone VoIP

Reviews:

Related manuals for 7941G - Unified IP Phone VoIP

Brands by name

Popular brands