manualshive.com logo in svg

Cisco 2975 - Catalyst LAN Base Switch, Software Configuration Manual

The Cisco 2975 Catalyst LAN Base Switch offers streamlined network management with robust features. Enhance your networking capabilities with ease by downloading the user manual from our website, completely free. Explore in-depth specifications and configurations to maximize the potential of this cutting-edge Cisco switch.

Share
Download
background image

C H A P T E R

 

6-1

Catalyst 2975 Switch Software Configuration Guide

OL-19720-02

6

Managing Switch Stacks

This chapter provides the concepts and procedures to manage Catalyst 2975 stacks. See the command 
reference for command syntax and usage information.

The switch command reference has command syntax and usage information.

  •

Understanding Stacks, page 6-1

  •

Configuring the Switch Stack, page 6-17

  •

Accessing the CLI of a Specific Member, page 6-22

  •

Displaying Stack Information, page 6-22

  •

Troubleshooting Stacks, page 6-23

Caution

A stack can have only Catalyst 2975 member switches.

For other switch stack-related information, such as cabling the switches through their stack ports and 
using the LEDs for switch stack status, see the hardware installation guide.

Understanding Stacks

A 

switch stack

 is a set of up to nine Catalyst 2975 switches connected through their stack ports. One of 

the switches controls the operation of the stack and is called the 

stack master

. The stack master and the 

other switches in the stack are 

stack members

. Layer 2 and Layer 3 protocols present the entire switch 

stack as a single entity to the network.

Note

A switch stack is different from a 

switch cluster

. A switch cluster is a set of switches connected through 

their LAN ports, such as the 10/100/1000 ports. For more information about how switch stacks differ 
from switch clusters, see the “Planning and Creating Clusters” chapter in the 

Getting Started with Cisco 

Network Assistant

 on Cisco.com.

The master is the single point of stack-wide management. From the master, you configure:

  •

System-level (global) features that apply to all members

  •

Interface-level features for each member

If the stack master is running the cryptographic version (that is, supports encryption) of the software, the 
encryption features are available. 

Summary of Contents for 2975 - Catalyst LAN Base Switch























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2975 - Catalyst LAN Base Switch

B&K HD6 Product Manual preview
HD6
Brand: B&K Pages: 2
B&B Electronics 232BSS4 Manual preview
232BSS4
Brand: B&B Electronics Pages: 45
Rack World CAT5 Quick Setting Manual preview
CAT5
Brand: Rack World Pages: 4
UNICOM DynaGST/2402G GEP-33224T-1 Specifications preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 1
UNICONTROL Electronic Cleveland Controls RSS-498-013 Manual preview
Cleveland Controls RSS-498-013
Brand: UNICONTROL Electronic Pages: 2
HPM XL770T Product Information preview
XL770T
Brand: HPM Pages: 4
Yamamoto Electric Works Co., Ltd. MS65F Instruction Manual preview
MS65F
Brand: Yamamoto Electric Works Co., Ltd. Pages: 15
WoMaster DS105 Quick Installation Manual preview
DS105
Brand: WoMaster Pages: 2
PureLink HDS-21R Owner'S Manual preview
HDS-21R
Brand: PureLink Pages: 10
West Mountain Radio PWRguard PLUS Operating Manual preview
PWRguard PLUS
Brand: West Mountain Radio Pages: 10
SMART Hub VE220 Installation And User Manual preview
Hub VE220
Brand: SMART Pages: 46
S&C Omni-Rupter Series Installation And Operation Manual preview
Omni-Rupter Series
Brand: S&C Pages: 31
Lantech IES-5222T Series User Manual preview
IES-5222T Series
Brand: Lantech Pages: 30
Harman AMX PR01-0808 User Manual preview
AMX PR01-0808
Brand: Harman Pages: 50
Tabs TBGW100-915 Reference Manual preview
TBGW100-915
Brand: Tabs Pages: 4
S&S Northern Merlin CS1 User Manual preview
Merlin CS1
Brand: S&S Northern Pages: 8
nedis VMAT3482AT Manual preview
VMAT3482AT
Brand: nedis Pages: 24
Dusun DSW-080 User Manual preview
DSW-080
Brand: Dusun Pages: 18

Brands by name

Popular brands

Load more brands