Cisco 12000 - Series Chassis Modular Expansion Base Hardware Installation Manual Download Page 36

Page: 36 / 132

1-16

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 1 Overview: Cisco 12000 Series Router SPA Interface Processors

Cisco 12000 SIP-501 Overview

The Cisco 12000 SIP-501 LEDs are described in

Table 1-12

Cisco 12000 SIP-501 Physical Specifications

The Cisco 12000 SIP-501

physical specifications are shown in the following table.

SPA Subslot Numbering on the Cisco 12000 SIP-501

The Cisco 12000 SIP-501 accepts up to 4 single-width SPAs or 1 dual-width SPA.

Figure 1-15

shows a Cisco 12000 SIP-501

with 2 SPAs installed. The left SPA slot is subslot 0 and the

right SPA slot is subslot 1. If one dual-width SPA is installed, it is recognized as being in subslot 0.

Figure 1-15 Subslot Locations for the 1-Port 10-Gigabit Ethernet SPA

SPA subslot 1

Status LED

SPA subslot 2

Rate LED

SPA subslot 3

Table 1-12

Cisco 12000 SIP-501 LEDs

LED Label

Color

State

Meaning

Status

Yellow

SIP is powered and IOS is loading.

Green

SIP is active.

Rate

Off

SIP is SIP-401 or SIP-501.

Green

SIP is SIP-601.

Table 1-13

Cisco 12000 SIP-501 Physical Specifications

Description

Specifications

Physical dimensions

Occupies one line card slot on a Cisco 12000 Series Router

Shipping weight

10kg

Operating temperature

32 to 104°F (0 to 40°C)

Relative humidity

10 to 90 percent, noncondensing

Storage temperature

–4 to 149°F (–20 to 65°C)

12000-SIP-600

116872

STAT

SPA-1XTENGE-XFP-A

ACTIVE/LINK

SPA10X1GE-A

ATUS

A/L

Summary of Contents for 12000 - Series Chassis Modular Expansion Base





































































































































Search results

Summary of Contents for 12000 - Series Chassis Modular Expansion Base

Reviews:

Related manuals for 12000 - Series Chassis Modular Expansion Base

Brands by name

Popular brands

Cisco 12000 - Series Chassis Modular Expansion Base, Hardware Installation Manual

Search results

Summary of Contents for 12000 - Series Chassis Modular Expansion Base

Reviews:

Related manuals for 12000 - Series Chassis Modular Expansion Base

Brands by name

Popular brands