Cisco 12000 - Series Chassis Modular Expansion Base Hardware Installation Manual Download Page 89 | Manualshive

Page: 89 / 132

background image

2-47

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA, 4-Port OC-3c/STM-1 POS SPA, and 8-Port

The SFP optical transceiver modules used with the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and
OC-12c/STM-4 POS SPA configured for OC-3 and the 4-Port and 8-Port OC-3c/STM-1 POS SPA
provide the following optical fiber options:

•

Multimode—155.52-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)

Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.

•

Single-mode—155.52-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ± 0.5 microns. (Nominal
diameter is approximately 10/125 microns.)

The SFP optical transceiver modules used with the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and
OC-12c/STM-4 POS SPA configured for OC-12 provide the following optical fiber options:

•

Multimode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)

Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.

•

Single-mode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ± 0.5 microns. (Nominal
diameter is approximately 10/125 microns.)

For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable (see

Figure 2-31

) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).

Use single-mode (for short-, intermediate- or long-reach configurations) or multimode optical fiber
cable to connect your router to a network or to connect two OC-3-equipped or OC-12-equipped routers
back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be
connected back-to-back without using an attenuator between the two of them.

Figure 2-31 LC-Type Cable

/ /

/ /

/ /

TX

RX

84929

«
...
87
88
89
90
91
...
»

Summary of Contents for 12000 - Series Chassis Modular Expansion Base





































































































































Reviews:

No comments

Related manuals for 12000 - Series Chassis Modular Expansion Base

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: Salto Pages: 2

Brand: Conceptronic Pages: 230

Brand: Allied Telesis Pages: 1

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

Brand: StarTech.com Pages: 9

Brand: AMX Pages: 1

Brand: Matrix Switch Corporation Pages: 60

Brand: OneAccess Pages: 47

Brand: Lantronix Pages: 75

Brand: Edimax Pages: 15

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

Monochrome Image Acquisition Device NI 1410

Brand: National Instruments Pages: 34

Brand: C&H Technologies Pages: 50

Brand: Vivotek Pages: 317

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands