Cisco 10000-2P2-2DC Software Configuration Manual Download Page 81 | Manualshive

Page: 81 / 624

background image

2-19

Cisco 10000 Series Router Software Configuration Guide

OL-2226-23

Chapter 2 Scalability and Performance

Configuring the Cisco 10000 Series Router for High Scalability

Placing PPPoA Sessions in Listening Mode

For better scalability and faster convergence of PPPoA, PPPoEoA, or LAC sessions, set sessions to
passive mode, using the

atm pppatm passive

command in ATM subinterface configuration mode. This

command places PPP or L2TP sessions on an ATM subinterface into listening mode. For large-scale
PPP terminated aggregation (PPPoA and PPPoEoA) and L2TP (LAC), the

atm pppatm passive

command is required.

Instead of sending out Link Control Protocol (LCP) packets to establish the sessions actively, the
sessions listen to the incoming LCP packets and become active only after they receive their first
LCP packet. When PPPoX is in passive mode, the LAC brings up the sessions only when the subscribers
become active and does not waste processing power polling all the sessions.

The following example configures passive mode for the PPPoA sessions on an ATM multipoint
subinterface:

Router(config)# interface atm 1/0.1 multipoint

Router(config-subif)# atm pppatm passive

Router(config-subif)# range range-pppoa-1 pvc 100 199

Router(config-subif-atm-range)# encapsulation aal5mux ppp virtual-template 1

Scaling L2TP Tunnel Configurations

To prevent head-of-the-line blocking of the IP input process and save system resources, configure the
following command in global configuration mode:

Router(config)#

vpdn ip udp ignore checksum

When you configure this command, the router directly queues L2TP Hello packets and Hello
acknowledgements to the L2TP control process. We recommend that you configure this command in all
scaled LAC and LNS L2TP tunnel configurations.

If you do not configure the

vpdn ip udp ignore checksum

command, the L2TP software sends the

packet to UDP to validate the checksum. When too many packets are queued to the IP input process, the
router starts selective packet discard (SPD), which causes IP packets to be dropped.

Note

Head-of-the-line blocking of the IP input process might occur in other non-L2TP configurations. A flush
occurring on an input interface indicates that SPD is discarding packets.

«
...
79
80
81
82
83
...
»

Summary of Contents for 10000-2P2-2DC

















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 10000-2P2-2DC

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brand: Nayar Systems Pages: 37

Brand: Hawking Pages: 2

Brand: TFortis Pages: 86

TOWERCHRON DP72

Brand: Grasslin Pages: 2

Brand: Global Sun Pages: 39

OptiBond 210 C Series

Brand: i-MO Pages: 16

Brand: ZyXEL Communications Pages: 8

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: Avigilon Pages: 12

Brand: Idis Pages: 28

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands