Cisco 10000-2P2-2DC Software Configuration Manual Download Page 112

Page: 112 / 624

3-28

Cisco 10000 Series Router Software Configuration Guide

OL-2226-23

Chapter 3 Configuring Remote Access to MPLS VPN

Configuration Tasks for RA to MPLS VPN

Example 3-9

assigns a VPN ID to the VRF named

vpn1

Example 3-9

Configuring a VPN ID

Router(config)# ip vrf vpn1

Router(config-vrf)# vpn id al:3f6c

Router(config-vrf)# end

Configuring and Associating Virtual Private Networks

To add a virtual private network (VPN) service to your MPLS configuration, you perform the following
tasks:

•

Configure VPNs

•

Associate VPNs with a virtual template interface

Configuring Virtual Private Networks

To configure dial-in and dial-out virtual private networks (VPNs), perform the following tasks:

•

Enable a VPN tunnel

•

Configure VPN tunnel authentication

For more information about configuring virtual private networks, see the “Configuring Virtual Private
Networks” chapter in the

Cisco IOS Dial Technologies Configuration Guide, Release 12.2

. This chapter

describes the procedures used to configure, verify, monitor, and troubleshoot VPNs and also provides
configuration examples.

Associating VPNs with a Virtual Template Interface

After you configure the VPNs, associate each one with a virtual template interface. To do this
association, perform the following tasks:

•

Creating a VRF Configuration for a VPN, page 3-28

•

Associating a VRF Configuration for a VPN with a Virtual Template Interface, page 3-29

Note

Do not enable VPN service on the fa0/0/0 management interface. The configuration for this
interface is included in the configuration file.

Creating a VRF Configuration for a VPN

To create a VRF configuration for a VPN, enter the following commands beginning in global
configuration mode:

Command

Purpose

Step 1

Router(config)#

ip vrf

vrf-name

Enters VRF configuration mode and defines the VPN routing
instance by assigning a VRF name.

Step 2

Router(config-vrf)#

route-distinguisher

Creates routing and forwarding tables.

Summary of Contents for 10000-2P2-2DC

















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 10000-2P2-2DC

Reviews:

Related manuals for 10000-2P2-2DC

Brands by name

Popular brands

Cisco 10000-2P2-2DC, Software Configuration Manual

Search results

Summary of Contents for 10000-2P2-2DC

Reviews:

Related manuals for 10000-2P2-2DC

Brands by name

Popular brands