manualshive.com logo in svg

Cisco 10000-2P2-2DC, Software Configuration Manual

The Cisco 10000-2P2-2DC is a high-performance networking device that requires proper software configuration to optimize its functionality. Ensure smooth operation with the comprehensive Software Configuration Manual, available for free download from manualshive.com. This manual provides step-by-step instructions to help you set up and customize your Cisco 10000-2P2-2DC for seamless network connectivity.

Share
Download
background image

C H A P T E R

 

21-1

Cisco 10000 Series Router Software Configuration Guide

OL-2226-23

21

Configuring L2VPN Interworking

Interworking is a transforming function that is required to interconnect two heterogeneous alternating 
currents (ACs). Several types of interworking functions exist. The function that is used would depend on 
the type of ACs being used, the type of data being carried, and the level of functionality required. The 
two main L2VPN interworking functions supported in Cisco IOS Software are bridged and routed 
interworking.

Layer 2 transport over MPLS and IP already exists for like-to-like attachment circuits, such as 
Ethernet-to-Ethernet or PPP-to-PPP. L2VPN Interworking builds on this functionality by allowing 
disparate attachment circuits to be connected. An interworking function facilitates the translation 
between different Layer 2 encapsulations. In earlier releases, the Cisco 10000 series router supported 
only bridged interworking, which is also known as Ethernet interworking. However, from Cisco IOS 
Release 12.2(33)XNE, the Cisco 10000 series router also supports routed interworking. 

This chapter describes the following L2VPN interworking features:

  •

Bridged Interworking

  •

Routed Interworking

Bridged Interworking

Bridged interworking is used when Layer 2 (L2) packets are considered without regard for Layer 3 
contents. No routing participation by the Internet Service Provider (ISP) exists. In Cisco IOS Release 
12.2(33)SB, the Ethernet (port) over MPLS pseudowire is supported for bridged interworking. 
Therefore, this type of interworking function is also called Ethernet Interworking.

In bridged interworking, Ethernet frames that are extracted from the attachment circuit (AC) are sent 
over the MPLS pseudowire. In the case of 802.1 Q AC, the VLAN tag is removed. The pseudowire 
functions in the Ethernet (VC type 0x0005) like-to-like mode. The interworking function at the Native 
Service Processor (NSP) performs the required adaptation based on AC technology. Non-Ethernet 
frames are dropped.

The following bridged interworking features are explained in the chapter:

  •

Ethernet to VLAN—Bridged Interworking, page 21-2

  •

Ethernet/VLAN to ATM AAL5 Interworking, page 21-5

  •

Ethernet/VLAN to Frame Relay Interworking, page 21-17

  •

Verifying L2VPN Interworking, page 21-30

Summary of Contents for 10000-2P2-2DC

















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 10000-2P2-2DC

3Com 3CR860-95 - OfficeConnect Secure Router Features And Benefits preview
3CR860-95 - OfficeConnect Secure Router
Brand: 3Com Pages: 2
3Com 3C905-TX Installation Manual preview
3C905-TX
Brand: 3Com Pages: 26
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
Watchguard XTM 5 Series Hardware Manual preview
XTM 5 Series
Brand: Watchguard Pages: 24
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Brand: pivotal Pages: 2
Perle IOLAN MDC User Manual preview
IOLAN MDC
Brand: Perle Pages: 491
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Brand: Idis Pages: 16
AirLive Ether-GSH24T v3 Quick Setup Manual preview
Ether-GSH24T v3
Brand: AirLive Pages: 2
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
Comet Labs 24-Port 1000BASE-T User Manual preview
24-Port 1000BASE-T
Brand: Comet Labs Pages: 44
UNICOM DynaGST/2402G GEP-33224T-1 User Manual preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 17
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
Calix GigaSpire BLAST u4hm Installation Manual preview
GigaSpire BLAST u4hm
Brand: Calix Pages: 45
NETGEAR WNR2000v2 - Wireless- N 300 Router User Manual preview
WNR2000v2 - Wireless- N 300 Router
Brand: NETGEAR Pages: 144
IBM BladeCenter 1/10 Gb Uplink Ethernet SwitchModule Installation Manual preview
BladeCenter 1/10 Gb Uplink Ethernet SwitchModule
Brand: IBM Pages: 58
Aztech DSL906 1DA Series Easy Start preview
DSL906 1DA Series
Brand: Aztech Pages: 15

Brands by name

Popular brands

Load more brands