CIS VCC-16MV02 Product Specification & Operational Manual Download Page 6

Page: 6 / 35

VCC-16MV02

Rev.905-0163-00

Product Outline

VCC-16MV02 is a Camera Link interfaced and 12M resolution B/W camera module. 12.29M pixels, 1.1 type (diagonal
Length 17.6mm) B/W CMOS sensor is utilized. Entire pixels can be read out at 1/53s with Full Configuration output.

Features

□

Global shutter CMOS sensor

□

Camera Link

Base, Medium, FULL, 8tap10bit, and 10tap8bit are supported.

□

Fixed trigger shutter mode, Pulse width trigger shutter mode

□

Full frame rate and video output are as below.

System Configuration

3.1.

Camera

□

Camera, VCC-16MV02

3.2.

Optional Accessories

□

M42-F Lens Mount Conversion Ring

3.3.

Free Software

Control software (for evaluation and demonstration)

※

CIS control panel software for evaluation purpose only is downloadable via our web.

CIS shall be exempted from taking responsibility and held harmless for damage or malfunction of your hardware and

software caused by using this control software. The purpose of this control software prepared is for users to check

operation and evaluate our products. Please be noted that CIS does not customize the program nor provide source

code.

3.4.

Packaging

□

Individual Carton

□

Master Carton (20pcs/carton)

Note) Master carton may vary depends on the quantity to be shipped.

2Tap Base Configuration

13.324fps

8bit/10bit

4Tap Medium Configuration

26.647fps

8bit/10bit

8Tap FULL Configuration

53.294fps

8bit

8Tap10bit Configuration

53.294fps

10bit

10Tap8bit Configuration

62.984fps

8bit

Factory Settings: 4Tap8bit Configuration

Summary of Contents for VCC-16MV02
































Search results

Summary of Contents for VCC-16MV02

Reviews:

Related manuals for VCC-16MV02

Brands by name

Popular brands

CIS VCC-16MV02, Product Specification & Operational Manual

Search results

Summary of Contents for VCC-16MV02

Reviews:

Related manuals for VCC-16MV02

Brands by name

Popular brands