Cirrus Logic CS5346 Manual Download Page 33

Page: 33 / 38

DS861PP3

CS5346

7.10.1

Clock Error (Bit 3)

Function:

Indicates the occurrence of a clock error condition.

7.10.2

Overflow (Bit 1)

Function:

Indicates the occurrence of an ADC overflow condition.

7.10.3

Underflow (Bit 0)

Function:

Indicates the occurrence of an ADC underflow condition.

7.11 Status Mask - Address 0Eh

Function:

The bits of this register serve as a mask for the Status sources found in the register

“Status - Address 0Dh”

on page 32

. If a mask bit is set to 1, the error is unmasked, meaning that its occurrence will affect the status

7.12 Status Mode MSB - Address 0Fh
7.13 Status Mode LSB - Address 10h

Function:

The two Status Mode registers form a 2-bit code for each Status register function. There are three ways to

update the Status register in accordance with the status condition. In the Rising-Edge Active Mode, the sta-

tus bit becomes active on the arrival of the condition. In the Falling-Edge Active Mode, the status bit be-

comes active on the removal of the condition. In Level-Active Mode, the status bit is active during the

condition.

00 - Rising edge active

01 - Falling edge active

10 - Level active

11 - Reserved

Reserved

ClkErrM

Reserved

OvflM

UndrflM

Reserved

ClkErr1

Reserved

Ovfl1

Undrfl1

Reserved

ClkErr0

Reserved

Ovfl0

Undrfl0

Summary of Contents for CS5346







































Search results

Summary of Contents for CS5346

Reviews:

Related manuals for CS5346

Brands by name

Popular brands

Cirrus Logic CS5346, Manual

Search results

Summary of Contents for CS5346

Reviews:

Related manuals for CS5346

Brands by name

Popular brands