Cirrus Logic CS4399 Manual Download Page 7

Page: 7 / 111

DS1113F1

CS4399

1.3 Pin Descriptions

GNDD

N/A

Digital and I/O Ground.

Ground for the I/O and core logic. GNDA,

GNDCP, GNDD must be connected to a common ground area
under the chip.

—

GNDA

N/A

Analog Ground.

Ground reference for the internal analog section.

GNDA, GNDCP, GNDD must be connected to a common ground
area under the chip.

—

GNDCP

12, 15,

F2, F3,

N/A

Charge Pump Ground.

Ground reference for the charge pump

section. GNDA, GNDCP, GNDD must be connected to a common
ground area under the chip.

—

V
VCP_FILT–

21
18

VCP/

I/O

Inverting Charge Pump Filter Connection.

Power supply from

the inverting charge pump that provides the positive/negative rail
for the analog output. When operating in external VCP_FILT
mode, these pins can directly take in supply voltage.

—

–VA

VA Negative Charge Pump Output.

Negative charge pump

output for DAC rail. It is derived from VA.

—

FLYP_VA
FLYN_VA

–VA Charge Pump Cap Positive/Negative Node.

Positive/

negative nodes for the DAC negative charge pump’s flying
capacitor.

—

FLYP_VCP

VCP/

–VCP Charge Pump Cap Positive Node.

Positive node for the

analog output negative charge pump’s flying capacitor.

—

FLYC_VCP

VCP/

–VCP Charge Pump Cap Center Node.

Center node for the

analog output negative charge pump’s flying capacitor.

—

FLYN_VCP

VCP_

FILT±

–VCP Charge Pump Cap Negative Node.

Negative node for the

analog output negative charge pump’s flying capacitor.

—

TSO

N/A

I/O

Test Output.

—

TSI

—

D3, F5

Test Input.

—

1.The power supply is determined by ADPT_PWR setting (see

Section 4.3.1

). VP is used if ADPT_PWR = 001 (VP_LDO Mode) or when necessary for

ADPTPWR = 111 (Adapt-to-Signal Mode).

Table 1-1. Pin Descriptions

(Cont.)

Pin Name

QFN

Pin #

WLCSP

Ball

Power

Supply

I/O

Pin Description

Internal

Connection

Digital I/O

Driver

Digital I/O

Receiver

Ground

Charge Pump

Test

Summary of Contents for CS4399
















































































































Search results

Summary of Contents for CS4399

Reviews:

Related manuals for CS4399

Brands by name

Popular brands

Cirrus Logic CS4399, Manual

Search results

Summary of Contents for CS4399

Reviews:

Related manuals for CS4399

Brands by name

Popular brands