background image

03

This manual provides commissioning information about Wallbox eNext series, which 
has been designed and tested to allow electric vehicle charging according to IEC 
61851-1:2017.

This document has different sections such as step-by-step installation procedure and 
technical data.

ELECTRICAL RISK

Necessary precautions shall be taken to prevent any electrical risk 
while the operations are carried out within the unit.

Unit must be disconnected from any power source during 
commissioning.

ATTENTION!

Indicates that damage to property can occur if appropriate 
precautions are not taken.

(*) These compliances only apply to eNext Elite Model

So, hello!

THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT 

SAFETY INFORMATION IN THIS DOCUMENT

• 

Complies with IEC 61851, Electric vehicle conductive charging 
system (IEC 61851-1:2017 and IEC 61851-21-2:2018).

• 

Complies with IEC 62196, Plugs, socket-outlets, vehicle 
couplers and vehicle inlets (IEC 62196-1  and IEC 62196-2). 

• 

Directives: 2014/35/UE, LVD;2014/30/UE, EMC.

• 

RFID complies with ISO/IEC 14443A/B *

• 

Modem 4G complies with IEC 60950-1 and CE/RED *

Summary of Contents for Wallbox eNext Series





































Reviews: